Bedienungsanleitung Milwaukee DCM2 180C (Seite 6 von 54) (Alle Sprachen)

641704

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Mounting a core bit

WARNING!

To reduce the risk of injury, always unplug the tool before

changing accessories or making adjustments.

1. To mount a bit, grease the spindle (A2) and bit threads to prevent

corrosion and to help prevent the bit from locking on the spindle.

2. Slip one copper washer (provided in separate accessory bag with

the water shut-off valve components) onto the spindle against the

spindle shoulder. The bag should contain an extra copper washer;

save it for future use.

3. Thread the bit securely onto the spindle.

Operation

WARNING!

To reduce the risk of injury, always check the work area for

hidden wires before coring.

WARNING!

To reduce the risk of injury, always use a water collection device

and follow the manufacturer’s instructions. The diamond coring

equipment must be grounded. Wear insulated footwear and

gloves for extra protection against shock hazards.

Using the Residual Current Device (E13)

Always test the Residual Current Device before using the Coring Motor

as follows:

NOTE: Turn OFF tool mains switch before resetting Residual Current

Device.

1. Connect the motor to a power source. Press the Residual Current

Device green "ON" button. The red light should glow.

2. Press the black "OFF" button. The red light should stop glowing.

3. If the Residual Current Device does not trip or if it switches OFF

repeatedly whenever Coring Motor is switched ON, the entire combi-

nation must be checked. Any further use or operation is not permitted

under such circumstances.

4. Start the Coring Motor. Make sure the Residual Current Device red

light glows and that the Coring Motor works properly.

If you cannot switch on or activate the residual current device, then:

• Try plugging the tool into another mains socket.

• Check for correct functioning of mains socket.

• Have mains socket checked by an electrician.

Supply an adequate water flow

An adequate supply of water must flow freely and constantly during the

entire cut. Coring Motors are equipped with a built-in water passage to

allow water to flow down the inside and up around the outside of the bit.

This acts to cool the bit and flush cuttings from the hole.

Starting and stopping the Coring Motor

To start the Coring Motor flip rocker switch (F15) to "ON" or "I".

To stop the Coring Motor flip rocker switch (F15) to "OFF" or "O".

Circuit Breaker

The circuit breaker will trip if the Coring Motor is overloaded. To reset

the circuit breaker, flip the rocker switch (F15) to "OFF" and press circuit

breaker button (F16).

Selecting speed

Coring Motors operate in either high or low speed. Use low speed for

large diameter bits and high speed for small diameter bits (see Coring

Motor Specifications).

The gear shift lever (A4) on the Coring Motor is labeled:

for low speed

for high speed

Coring

WARNING!

To reduce the risk of injury, ALWAYS wear safety goggles or

glasses with side shields.

1. Select a bit following guidelines in the specifications chart and install.

2. With the motor OFF, adjust the shift lever to either low speed or high

speed following guidelines in the specifications chart. DO NOT SHIFT

SPEEDS WHEN THE CORING MOTOR IS ON.

3. Connect the water hose to the water shut-off valve assembly. Make

sure the connections do not leak. Set up a water collection system.

4. Turn the Coring Motor ON. Turn the water on so it flows freely through

the water shut-off valve. Turn the valve clockwise to increase water

flow and counterclockwise to decrease water flow.

5. When the cut is complete, pull the bit out of the hole with the motor

running. Once the bit is removed from the hole, turn the motor OFF.

Maintenance

Lubricating the Spindle For Shear Pin Models

Before each use, clean and lubricate the spindle or spindle sleeve with

grease to prevent the spindle from locking during coring.

Cleaning

Remove dust and debris from vents. Keep the tool clean, dry and free of

oil or grease. Use only mild soap and a damp cloth to clean your tool

since certain cleaning agents and solvents are harmful to plastics and

other insulated parts.

Repairs

Use only identical

MILWAUKEE

replacement parts. Always take the tool

to an authorized

MILWAUKEE

service center for repairs and mainte-

nance.

Accessories

Copper Washer

Catalog Number 45-88-8565

For replacement of lost copper washer required for coring.

3/16" socket wrench

Catalog Number 49-96-0085

For mounting Dymodrills to motor mounts or spacer assemblies.

1-3/8" open end wrench

Catalog Number 49-96-4700

For mounting and removing coring bits from the Dymodrill.

3/32" hex wrench

Catalog Number 49-96-0050

For set screw on the water collar.

Shear Pins

Catalog Number 44-60-0032

Hardened Shear Pin

Catalog Number 44-60-0065

Soft Shear Pin

English

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Milwaukee DCM2 180C Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info