Bedienungsanleitung Minimoka CM-4758 (Seite 21 von 32) (Englisch, Spanisch)

727618

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Note:

If the following warning appears on the display, the water

tank must topped up before the next drink is dispensed.

Otherwise further function is not possible.

Before inserting the water tank, make sure that it is dry

on the outside. Wipe the water tank shaft dry also before

inserting the water tank.

Filling the coffee bean container:

- Fold back the lid of the coffee container (K).

- Fill the container with fresh coffee beans.

- Then close the container again.

Use:

- Connect the appliance to the mains.

- Turn the appliance on, by pressing the on/off button

andholdingitdownbriey.Duringtheheatingprocedure

(approx.30seconds)thefollowingdisplayashes.

- When the operating temperature has been reached,

the coffee machine automatically performs a rising cycle.

Watermayowhereintothedriptray.

-When the rising cycle is completed, the coffee machine

is ready to use. The following displays light up during

initial start-up:

Determining the water hardness

Beforeusingthecoffeemachineforthersttime,it

should be set to the appropriate water hardness for

your region. You can determine the water hardness with

the help of the test strip (18) supplied with the coffee

machine.

Proceed as follows:

- Dip the test strip into cold water for 1 second and shake

off the excess water. After approximately 1 minute, the

water hardness can read from the pink-coloured areas.

Menu settings

The menu function must be accessed to undertake va-

rious settings – for example, to set the determined water

hardness level.

To do this, press buttons 2 and 3 simultaneously for

approx. 3 seconds.

Thesymboldisplaywillbrieylightupasablinkingline,

then the display will change to the current settings. The

following parameters can be set:

• Water tank illumination via button 2

• Water hardness level via button 3

• Coffee temperature via button 4

• Switch-off time via button 5.

•Savetheentriesandquitthemenubyconrmingwith

OK (button 6). If you do not press OK, the program will

automatically return to the operating mode after approx.

60 sec. without saving the new settings.

Setting and storing the water hardness:

- Switch to the menu function by simultaneously pressing

buttons 2 and 3 for approx. 3 seconds. The function

displaysofthemenuwillashrstinablinkingline,then

the current settings will be displayed.

Then press key 3 repeatedly until the required hardness

degree is set.

The image below shows the displays for the 4 possible

hardness degree settings.

Store the input by pressing “OK” (button 6). All function

displaysofthemenuashforapprox.3secondstocon-

rm.Theappliancethenreturnstothenormaloperating

mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Minimoka CM-4758 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info