Bedienungsanleitung Mio MiVue 886 (Seite 8 von 30) (Englisch)

790898

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

3. When adjusting the angle of mounting, make sure that the camera’s view is

parallel with the level ground and the ground/sky ratio is close to a 50/50 split.

* 50/50

Using the device mount

U-type mount (Figure 1-A)

O-type mount (Figure 2-B)

Install your Mio on the motorcycle or helmet by using the

provided device mount.

Using the charging cable

USB charging cable (Figure 2-A)

5V USB waterproof charging cable (Figure 2-B)

You should fully charge the battery before you start using

it for the very rst time. To charge the battery, plug the

provided charging cable into the Micro-USB connector on

your Mio and the other end into a power source (5V DC /

2A; not provided).

Using the power cable

12V waterproof power cable (Figure 2-C)

Check and conrm the motorcycle wire by using the

electricity tester.

Connect the red wire (ACC) of the power cable to the

motorcycle wire from which the power is not supplied

when the motorcycle is turned off.

The black wire (GND) must be connected to the metal

part of the motorcycle for grounding. If not grounded, this

product may not work properly. You can use a screw to

attach the black wire to the motorcycle (try to nd a screw

hole on any metal part).

Using the rear camera kit

Rear camera with 12V waterproof power cable (Figure

2-D)

Rear camera with 5V USB charging cable (Figure 2-E)

Follow the previous instructions to connect the power

cable / charging cable, and then connect the rear camera.

Installing the ferrite cores

Depending on your model, ferrite cores may be provided

to eliminate electromagnetic interference. Follow the

instructions (Figure 2-F) to install the ferrite cores on the

rear camera cable.

Revision: R00

(7/2019)

5615N6280002 R00

Torque: 15kgf.cm

ACC

GND

10 cm 10 cm

Using the device mount

U-type mount (Figure 1-A)

O-type mount (Figure 2-B)

Install your Mio on the motorcycle or helmet by using the

provided device mount.

Using the charging cable

USB charging cable (Figure 2-A)

5V USB waterproof charging cable (Figure 2-B)

You should fully charge the battery before you start using

it for the very rst time. To charge the battery, plug the

provided charging cable into the Micro-USB connector on

your Mio and the other end into a power source (5V DC /

2A; not provided).

Using the power cable

12V waterproof power cable (Figure 2-C)

Check and conrm the motorcycle wire by using the

electricity tester.

Connect the red wire (ACC) of the power cable to the

motorcycle wire from which the power is not supplied

when the motorcycle is turned off.

The black wire (GND) must be connected to the metal

part of the motorcycle for grounding. If not grounded, this

product may not work properly. You can use a screw to

attach the black wire to the motorcycle (try to nd a screw

hole on any metal part).

Using the rear camera kit

Rear camera with 12V waterproof power cable (Figure

2-D)

Rear camera with 5V USB charging cable (Figure 2-E)

Follow the previous instructions to connect the power

cable / charging cable, and then connect the rear camera.

Installing the ferrite cores

Depending on your model, ferrite cores may be provided

to eliminate electromagnetic interference. Follow the

instructions (Figure 2-F) to install the ferrite cores on the

rear camera cable.

Revision: R00

(7/2019)

5615N6280002 R00

ACC

GND

Torque: 15kgf.cm

10 cm 10 cm

Using the device mount

U-type mount (Figure 1-A)

O-type mount (Figure 2-B)

Install your Mio on the motorcycle or helmet by using the

provided device mount.

Using the charging cable

USB charging cable (Figure 2-A)

5V USB waterproof charging cable (Figure 2-B)

You should fully charge the battery before you start using

it for the very rst time. To charge the battery, plug the

provided charging cable into the Micro-USB connector on

your Mio and the other end into a power source (5V DC /

2A; not provided).

Using the power cable

12V waterproof power cable (Figure 2-C)

Check and conrm the motorcycle wire by using the

electricity tester.

Connect the red wire (ACC) of the power cable to the

motorcycle wire from which the power is not supplied

when the motorcycle is turned off.

The black wire (GND) must be connected to the metal

part of the motorcycle for grounding. If not grounded, this

product may not work properly. You can use a screw to

attach the black wire to the motorcycle (try to nd a screw

hole on any metal part).

Using the rear camera kit

Rear camera with 12V waterproof power cable (Figure

2-D)

Rear camera with 5V USB charging cable (Figure 2-E)

Follow the previous instructions to connect the power

cable / charging cable, and then connect the rear camera.

Installing the ferrite cores

Depending on your model, ferrite cores may be provided

to eliminate electromagnetic interference. Follow the

instructions (Figure 2-F) to install the ferrite cores on the

rear camera cable.

Revision: R00

(7/2019)

5615N6280002 R00

ACC

GND

Torque: 15kgf.cm

ACC

GND

10 cm 10 cm

Note: The installation illustrations are for your reference only. The placement of the devices and

cables may vary depending on the vehicle model. If you encounter any problems during installation,

contact a skilled installer (such as the service personnel of the vehicle) for assistance.

Mio MiVue 886 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info