Bedienungsanleitung Mitsubishi EX200U (Seite 31 von 49) (Englisch)

493643

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

EN-31

ENGLISH

1. Repeat steps 1-2 above.

2. Press to highlight Volume and press / to select a desired sound level.

Personalizing the projector menu display

The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect

the projection settings, operation, or performance.

• Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the

OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second

increments. Use / to select a suitable time frame.

• Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five

locations. Use / to select a preferred position.

• Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to

select your language.

• Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during

projector start-up. Use / to select a screen.

Shutting down the projector

1. Press POWER and a confirmation message displays prompting you.

If you don't respond in a few seconds, the message will disappear.

2. Press POWER a second time. The POWER indicator light flashes

orange, the projection lamp shuts down, and the fans will continue to run

for approximately 90 seconds to cool down the projector.

3. Once the cooling process finishes, the POWER indicator light is a

steady orange and fans stop.

4. Disconnect the power cord from the wall socket if the projector will not

be used in an extended period of time.

• To protect the lamp, the projector will not respond to any commands during the

cooling process.

• To shorten the cooling time, you can also activate the Quick Cooling function.

See "Quick Cooling" on page 36 for details.

• Do not unplug the power cord before the projector shutdown sequence is

complete or during the 90-second cooling down process.

• If the projector is not properly shut down, to protect the lamp, when you attempt

to re-start the projector, the fans will run for a few minutes to cool down. Press

POWER again to start the projector after the fans stop and the POWER

indicator light turns orange.

Direct power off

1. The AC power cord can be pulled out during the projector is on. To protect the lamp, wait about 10 minutes

before re-starting the projector. (When you attempt to re-start the projector, the fans may run for a few minutes

to cool down. In such cases, press POWER again to start the projector after the fans stop and the POWER

indicator light turns orange.

2. To protect the lamp, do not shut down the projector while the POWER indicator light is blinking green after

the lamp lights up.

3. Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without

closing the menu, the setting data of the menu may not be saved.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi EX200U Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info