Bedienungsanleitung Mitsubishi EX320U-ST (Seite 13 von 58) (Englisch)

493684

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

EN-13

ENGLISH

How to determine the position of the projector for a given screen size

1. Determine the aspect ratio of your screen, 16:9 or 4:3. If you have a 4:3 screen, refer to the table labeled

"(Standard)". If you have a 16:9 screen, refer to the table labeled "(16:9)".

2. Select your screen size.

3. Refer to the table and find the closest match to your screen size in the left columns labeled "Screen". Using this

value, look across this row to the right to find the corresponding average distance from screen value in the

column labeled "Distance from the screen: L". This is the projection distance.

4. On that same row, look across to the right column and make note of the "Hd" value. This will determine the final

vertical offset placement of the projector in relation to the edge of the screen.

5. The recommended position for the projector is aligned perpendicular to the horizontal center of the screen, at the

distance from the screen determined in step 3 above, and offset by the value determined in step 4 above.

For example, if you are using a 4:3 aspect ratio, 100-inch screen, distance from the screen is 1.2 m and with a vertical

offset of 23 cm.

If you place the projector in a different position (to that recommended), you will have to tilt it down or up to center the

image on the screen. In these situations, some image distortion will occur. Use the Keystone function to correct the

distortion. See "Correcting keystone" on page 25 for details.

How to determine the recommended screen size for a given distance

This method can be used for situations where you have purchased this projector and would like to know what screen

size will fit in your room.

The maximum screen size is limited by the physical space available in your room.

1. Measure the distance between the projector and where you want to position the screen. This is the projection

distance.

2. Refer to the table "(Standard)" or "(16:9)", and find the closest match to your measurement in the distance from

the screen column. If the min and max values are available on the table, check that your measured distance is

between the min and max distances listed on either side of the average distance value.

3. Using this value, look across that row to the left to find the corresponding "Screen". That is the projected image

size of the projector at that projection distance.

4. On that same row, look across to the right column and make note of the "Hd" value. This will determine the final

placement of the screen in relation to the horizontal plane of the projector.

For example, if your measured projection distance was 1.5 m and your screen aspect ratio is 4:3, the closest match in

the "Distance from the screen: L" column is 1.5 m. Looking across this row shows that a 120-inch screen is required.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi EX320U-ST Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info