Bedienungsanleitung Mitsubishi FDTC35VF (Seite 13 von 24) (Englisch)

604739

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

7 Press SET button (Fixing of the upper

limit position)

The upper limit position is fixed and the setting position is

displayed for two seconds. Then proceed to lower limit position

selection display.

[EXAMPLE]

“

” (lights for two seconds)



“ ” (shows current setting)

8 Press ▲ or ▼ button (Selection of lower limit

position)

Select the lower limit position of louver.

“position 1” is the most horizontal, and “position 6” is the most

downwards.

“position

” is to return to the factory setting. If you need to

change the setting to the factory setting, use “position

”.

“

” (the most horizontal)

“

”

“

”

“

”

“

”

“

” (the most downwards)

“

” (return to the position of shipment)

9 Press SET button (Fixing of the lower limit

position)

The upper limit position and lower limit position are fixed, the set

positions lights for two seconds, and then the setting is completed.

• After the setting is completed, the louver which was set

moves from the original position to the lower limit position,

and goes back to the original position again. (This operation

is not performed if the indoor unit and/or indoor unit fan is in

operation.)

[Example]

“

” (lights for two seconds)



“ ”



“

Press button.

Louver adjusting mode ends and returns to the original display.

HOW TO SET THE AIR FLOW DIRECTION

< WIRED REMOTE CONTROL >

NOTICE

(downwards)

(horizontal)

the position of the louver

[EXAMPLE] For Upper position 2, Lower position 6

Lower

position

Movable

range

Upper

position

• When plural remote controllers are connected, louver position setting cannot be set by slave remote control.

• If you press RESET button during settings, the display will return to previous display. If you press

button during settings, the mode will end and the original display will return, and the settings that have not been

completed will become invalid.

Note : If the upper limit position number and the lower limit

position number are set to the same position, the louver

is fixed at that position. And auto swing does not function.

Clean the filter frequently

☞

See page 16

If the filter is clogged…

• The cooling/heating capacity will get reduced. Moreover it leads

to waste of electricity and larger operation noise.

• It may cause failure.

• Dew may form and drop during cooling.

Do not block the inlet and outlet grilles of the

indoor and outdoor units.

Excessive load to the unit may cause failure.

Keep moderate room temperature

Too much cooling or heating is not good for your health. It will also

waste the electricity.

Block direct sunlight and prevent draft

Block direct sunlight with blinds and curtains during cooling. Close

the windows and doors except when ventilation is necessary.

Adjust the airflow properly

Do not expose yourself directly to the airflow for too long time. For

small animals and plants, it is harmful as well.

If you feel cold underneath your feet during heating

If the ceiling is so high that the warm airflow does not circulate

underneath your feet, it is recommended to use a circulator.

Consult your dealer for more detail.

Stop the operation and turn the power supply

off if there are any possibility of lightning

strikes during a thunderstorm.

Lightning strikes may lead to the failure of air-conditioning system.

FOR COMFORTABLE USE

The filter should be cleaned when

the “Filter cleaning” message

is displayed, and at the ends of

cooling and heating seasons.

HOW TO OPERATE VENTILATION (WHEN A VENTILATOR IS INSTALLED) < WIRED REMOTE CONTROL >

1 Press VENTI button.

“ ” is displayed, and the ventilation operation begins.

Stop

Press VENTI button again.

When the ventilator is set to “NO VENTI LINK”, the ventilator can be turned on and off independently regardless

of the operation of the air conditioner.

When the ventilator is set to “VENTI LINK”, the ventilator operation will be interlocked with the air conditioner

operation.

NOTICE

• If no ventilator is connected, no operation can be performed by

pressing the ventilation button. (“ ” is displayed).

VENTILATION OPERATION NOT LINKED WITH UNIT’S

OPERATION

1 Press button.

If a ventilator is connected, ventilation will operate automatically.

“ ” is displayed.

Stop

Press button again.

NOTICE

• No operation can be performed by pressing the ventilation button.

(“ ” is displayed).

VENTILATION OPERATION LINKED WITH UNIT’S OPERATION

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi FDTC35VF Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi FDTC35VF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info