Bedienungsanleitung Mitsubishi hc1100 (Seite 21 von 39) (Englisch)

215923

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

EN-21

ENGLISH

POWER STATUS

C. Projecting images

Preparation:

• Remove the lens cap.

• Turn on the power of the connected computer.

1. Conﬁ rm the POWER indicator lights-up red.

• If the projector was turned off before the lamp had cooled down sufﬁ ciently, the fan may start rotating and the

POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the

fan stops rotating, press the power button to turn back on the POWER indicator.

2. Press the POWER button on the projector or ON ( I ) button on the remote control.

• It may take about one minute for the lamp to light up.

• The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

• Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the

lens cap.

• After the POWER button is pressed, the image may ﬂ icker before the lamp becomes stable. This is not a prod-

uct malfunction.

•

The STANDARD lamp mode is activated by default whenever the projector is turned on. When the LOW LAMP

MODE has been chosen, the default STANDARD lamp mode is switched to the LOW lamp mode in 1 minute.

• The projector starts warming up when the POWER button is pressed. During the warm-up process, images may

appear dark and no commands are accepted.

• By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when

the STATUS indicator blinks red. (See pages 33 and 36.)

3. Select an input source.

• Press the COMPUTER button on the projector or the COMPUTER or HDMI button on the remote control that is

corresponding to the terminal in use.

• The input source is switched between COMPUTER and HDMI every time you press the COMPUTER button on

the projector.

• Though it may take some time before an image is displayed on the screen depending on the type of the input

signal, such symptom is not a malfunction.

• Images may not be projected in the correct position, depending on the type of the input signal. In such a case,

press the AUTO POSITION button. (See page 22.)

• The projector automatically selects the appropriate signal format. The selected signal format is displayed on the

screen.

• The

COMPUTER and HDMI buttons don’t function while the menu is being displayed.

• When COMPUTER is chosen as the source, images supplied from the computer may ﬂ icker. Press the  or 

button on the remote control to reduce ﬂ icker, if it occurs.

4. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in

their speciﬁ ed sizes.

5. Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page

10.)

• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)

6. Adjust the size of the projected image by turning the ZOOM ring.

7. Adjust the focus by turning the FOCUS ring.

Repeat steps 4 to 7, if necessary.

POWER button

COMPUTER button

FOCUS ring

COMPUTER button

HDMI button

ZOOM ring

ON ( I ) button

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi hc1100 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info