Bedienungsanleitung Mitsubishi hc1100 (Seite 32 von 39) (Englisch)

215923

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

EN-32

(c)

(a)(b)

(c)

To replace the lamp:

1. Reverse the projector gently.

2. Loosen the screw (a) using a Phillips screwdriver (+), and

remove the lamp cover (b).

3. Loosen the screws (c) using a Phillips screwdriver (+).

4. Pull up the handle.

5. Pull out the lamp box by the handle while holding the

projector.

• Pull the lamp box out of the projector slowly. If it is

pulled out quickly, the lamp may break scattering glass

fragments.

• Do not spill liquid on the removed lamp box or do not

place it near any ﬂ ammable object or where children

can reach to prevent injury or ﬁ re.

6. Load a new lamp box securely into the projector in the right

orientation.

7. Put the handle back to the original position.

• Make sure that the handle is locked.

8. Tighten up the screws (c) using a Phillips screwdriver (+).

9. Tighten up the screw (a) using a Phillips screwdriver (+) to

secure the lamp cover.

Reset of the lamp operation time

Plug in the power cord and reset the lamp operation time by

holding down the





, and POWER buttons on the control

panel at the same time about three seconds.

Important:

• Unless these three buttons are pressed at the same time, the lamp operation time isn’t reset.

• Make sure that the STATUS indicator blinks twice and the lamp operation time is reset successfully.

• The projector doesn’t turn on if the lamp cover isn’t attached securely.

• Be sure to reset the lamp operation time whenever you replace the lamp.

• Do not reset the lamp operation time unless you replace the lamp.

• The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.

• Contact your dealer for a new lamp.

• This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be

regulated due to environmental considerations. For disposal or recycling information, please contact your local

authorities or the Electronic Industries Alliance: www.eiae.org. (For the U.S. only.)

Maintenance

Warning:

Do not use ﬂ ammable solvents (benzene, thinner, etc.) and ﬂ ammable aerosols when cleaning the projector body and

lens. Flammable substances may ignite causing ﬁ re or breakdown while the lamp is illuminating.

Caution:

Be sure to turn off the lamp and unplug the power cord from the wall outlet before you perform any maintenance on

the projector.

Cleaning of the projector and the ventilation slots

Use a soft cloth to clean the projector and the ventilation grilles. When the grilles become dirty, wipe them with a soft

cloth dampened with diluted mild detergent, and then wipe them with a dry cloth.

To protect the surface of the projector from fading or deteriorating:

• Do not spray insecticide on or inside the projector.

• Do not use benzine or thinner to clean it.

• Do not let rubber or plastic materials contact with projector.

Cleaning of the lens

Use a standard lens-cleaning brush or a piece of lens tissue dampened with lens cleaning ﬂ uid. The lens surface is

fragile. Use only recommended, nonabrasive lens-cleaning materials. Do not touch the lens with your ﬁ ngers.

Replacing the lamp (continued)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi hc1100 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info