Bedienungsanleitung Mitsubishi HC3100 (Seite 10 von 41) (Englisch)

493620

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

EN-10

Setting up your projector

A=B

Setting up the screen

Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the

projection angle of the projector. (See below.)

• Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of

the screen center.

• Do not install the screen where it is exposed to direct sunlight or lighting. Light directly reﬂecting on the screen

makes the projected images washed-out and hard to view.

SCREEN SIZE

You can keep the image display area within the screen by setting SCREEN SIZE in the IMAGE menu according to the

size of the actual screen.

When setting SCREEN SIZE to CINEMA SCOPE(2.35:1):

• CinemaScope size movies are projected in the full screen.

• Set ASPECT in the FEATURE menu to 16:9 when displaying Vista-size images. In this case, they are squeezed

horizontally.

• When ASPECT in the FEATURE menu is set to AUTO and 480p, 720p, or 1080i signal is input, the part for

displaying subtitles is not projected.

Then, set SCREEN SIZE to 720P(16:9) and adjust the image position using

VERTICAL LOCATION of the IMAGE menu. (To display the menu on the screen, adjust SHUTTER (U) of USER in

the SIGNAL menu to position the menu.)

Basic setup

Determine the distance from the screen to the projector according to the size of the images to be projected. (See

page 12.)

• Do not place this projector on a carpet or blanket because the exhaust vent and the intake vent on the bottom

surface are blocked and the projector would heat, causing a breakdown or ﬁre.

• Depending on the installation conditions, warm air that is emitted from the exhaust vents may ﬂow into the intake

vent, causing the projector to display

“TEMPERATURE!!” and then stop projecting images.

Adjusting the projection angle

This projector is provided with three feet for

adjusting the projection angle on the bottom

surface. Adjust the projection angle depending on

the position of the projector.

Adjustment of the projection angle

For the best projection, project images on a

ﬂat screen installed at 90 degrees to the ﬂoor.

If necessary, tilt the projector using the two

adjustment feet on the bottom of the projector.

1. Tilt up the projector to the appropriate angle.

2. Press the foot adjustment buttons next to the

adjustment feet (rear), and the adjustment feet

will come out.

3. Release the buttons to lock the adjustment feet

(rear) to that position.

4. Rotate the adjustment feet (rear) for ﬁne

adjustment.

After using the projector:

Put the adjustment feet (rear) back into the

projector by pressing the foot adjustment buttons.

• If necessary, rotate the adjustment feet (front) for

ﬁne adjustment.

When projected images are distorted to a

trapezoid:

When the screen and the projector are not placed

perpendicularly to each other, projected images

become trapezoidal. If you cannot make the

projector and the screen perpendicular to each

other by mechanical adjustments, adjust keystone.

(See page 18.)

• When the keystone adjustment is applied, the

correct aspect ratio may not be obtained.

• When the keystone adjustment is applied, the

resolution lowers. In addition, vertical stripes ap

pear and straight lines bend in images with com-

plicated patterns. To prevent such symptoms,

keep the screen and the projector perpendicular

to each other as much as possible.

• Though the projected image may be distorted

momentarily when you change the setting value

of the keystone adjustment, such symptom is not

a malfunction.

• Though the projected image may be distorted

depending on the setting value of the keystone

adjustment and the type of the input signal, such

symptom is not a malfunction. In such a case,

adjust the setting value within the range where

the projected image is not distorted.

• The setting value displayed at the time of the

keystone adjustment may vary depending on the

type of the input signal.

• The keystone mode does not function when the

REAL mode is applied.

• Displayed image may be distorted during key-

stone adjustment.

Screen

Adjustment feet

(rear)

VERTICAL LOCATION

You can adjust the vertical position of the displayed image using

VERTICAL LOCATION in the IMAGE menu.

(Example) To move the displayed image up:

Maximum panel size (WXGA 15:9)

Empty area

Set SCREEN SIZE in the IMAGE

menu to 720p(16:9)

Empty area

Set VERTICAL LOCATION

in the

IMAGE menu to +6.

• When you increase the value of VERTICAL LOCATION too much,

the displayed image may be out of the screen partially.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi HC3100 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info