Bedienungsanleitung Mitsubishi HC3200 (Seite 5 von 48) (Englisch)

493687

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

EN-5

WARNING:

Unplug immediately if there is something wrong

with your projector.

Do not operate if smoke, strange noise or odor comes

out of your projector. It might cause ﬁre or electric shock.

In this case, unplug immediately and contact your dealer.

Never remove the cabinet.

This projector contains high voltage circuitry. An

inadvertent contact may result in an electric shock.

Except as speciﬁcally explained in the User Manual do

not attempt to service this product by yourself. Please

contact your dealer when you want to ﬁx, adjust or

inspect the projector.

Do not modify this equipment.

It can lead to ﬁre or electric shock.

Do not keep using the damaged projector.

If the projector is dropped and the cabinet is damaged,

unplug the projector and contact your dealer for

inspection. It may lead to ﬁre if you keep using the

damaged projector.

Do not face the projection lens to the sun.

It can lead to ﬁre.

Use correct voltage.

If you use incorrect voltage, it can lead to ﬁre.

Do not place the projector on uneven surface.

Place the projector on a leveled and stable surface only.

Please do not place equipment on unstable surfaces.

Do not look into the lens when the projector is

operating.

It may hurt your eyes. Never let children look into the

lens when it is on.

Do not unplug the power cord during operation.

It can lead to lamp breakage, ﬁre, electric shock or

other trouble. It is best to wait for the fan to turn off

before turning the main power off.

Do not touch the air outlet grille and bottom plate,

which become hot.

Do not touch them or put other equipment close to

the air outlet grilles because they become hot during

operation. The heated air outlet grilles and bottom plate

may cause injury or damage to other equipment.

Also, do not put the projector on a desk that is easily

affected by heat.

Do not look into the air outlet grille when projector

is operating.

Heat, dust, etc. may blow out of it and hurt your eyes.

Do not block the air inlet and outlet grilles.

If they are blocked, heat may be generated inside the

projector, causing deterioration in the projector quality

and ﬁre.

Do not use ﬂammable solvents (benzene, thinner,

etc.) and ﬂammable aerosols near the projector.

Flammable substances may ignite causing ﬁre or

breakdown because the temperature inside the

projector rises very high while the lamp is illuminating.

Do not use the projector with condensation on it.

It can lead to breakdown or other failure.

Place of installation

For safety’s sake, refrain from setting the projector

at any place subjected to high temperature and high

humidity. Please maintain an operating temperature,

humidity, and altitude as speciﬁed below.

Operating temperature: between +41°F (+5°C) and

+95°F (+35°C)

Operating humidity: between 30% and 90%

Never put any heat-producing device under the

projector so that the projector does not overheat.

Do not install the projector to a place that is

unstable or subjected to vibration.

Do not install the projector near any equipment that

produces a strong magnetic ﬁeld.

Also refrain from installing the projector near any

cable carrying a large amount of current.

Place the projector on a solid, vibration free surface;

otherwise it may fall, causing serious injury or

damage.

Do not stand the projector on its end. It may fall,

causing serious injury or damage.

Slanting the projector more than ±10°(right and

left) or ±15°(front and rear) may cause trouble or

explosion of the lamp.

Do not place the projector near air-conditioning unit,

heater, or humidiﬁer to avoid hot or moist air to the

exhaust and ventilation hole of the projector.

•

Important safeguards (continued)

COMPLIANCE NOTICE OF FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced Radio/TV technician for help.

Changes or modiﬁcations not expressly approved by Mitsubishi could void the user’s authority to operate this

equipment.

COMPLIANCE NOTICE OF INDUSTRY CANADA

This Class B digital apparatus complies with Canadian ICES-003.

•

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi HC3200 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi HC3200

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info