Bedienungsanleitung Mitsubishi hc6500 (Seite 36 von 47) (Englisch)

215922

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

EN-36

This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness

may decrease during use. In such cases, replace the lamp with a new one as soon as possible. Be sure to replace the

lamp with a new lamp sold separately that is exclusive to this projector. Contact your dealer for purchase of the lamp.

Spare lamp VLT-HC7000LP

Warning:

Be careful not to drop the lamp ﬁ xing screws inside of the projector. Don’t put a metal piece or ﬂ ammable object

into the projector. Using the projector with any foreign object present inside may result in electric shock or ﬁ re.

When you can’t remove the foreign object from the inside, contact your dealer for removal.

Be sure to install the lamp securely. When the lamp isn’t installed properly, it won’t illuminate. Improper installation

may also result in ﬁ re.

Don’t shake the removed lamp or don’t lift it above your face. Your eyes may be injured by ﬂ ying or falling glass

fragments.

Don’t replace the lamp immediately after use because the lamp cover will be very hot. You may get burned. Turn

off the power using the POWER button. After the lamp goes out, wait about two minutes until the intake and

exhaust fans for cooling the lamp stop rotating. Then unplug the power cord, and wait at least one hour to allow

the lamp to cool down enough to the touch.

Do not touch the lamp directly. It may break and cause injury or burn.

Interval of lamp replacement

The recommended interval of lamp replacement is about 5000 hours*

of consecutive use. Such interval differs

depending on the operating environment and may be shorter than 5000 hours*

. Decrease in luminescence and/or

color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds 3750 hours*

the indicator will blink alternately between green and red (while the lamp is lit; when the lamp is not lit, the indicator

will be lit red only) and the lamp replacement message will appear on the screen for one minute everytime the lamp

is turned on. When the lamp has been used for about 4750 hours*

, the replacement message (LAMP EXCHANGE)

will appear on the screen for one minute every 25 hours*

thereafter. When the lamp operation time exceeds 5000

hours*

, the projector automatically shuts off and can’t be used until the lamp is replaced and the lamp

operation time is reset.

*1: Duration when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be

shorted.

*2: When LAMP MODE is set to STANDARD, this duration will be shorted to 2000 hours.

Caution:

Don’t remove the lamp for any purpose other than replacement. Unnecessary removal of the lamp may result in a

breakdown.

This projector uses a high-pressure mercury lamp as the light source. The high-pressure mercury lamp may

explode or fail to illuminate permanently because of an impact, scratch, or deterioration through use. The period

of time until explosion or permanent failure to illuminate varies considerably from lamp to lamp, depending on

operation conditions. Therefore, the lamp may explode soon after the start of use.

The possibility of explosion of the lamp increases if you use it beyond its replacement period. When the instruction

of lamp replacement appears, replace it with a new one immediately even if the lamp is still lighting normally.

When the high-pressure mercury lamp explodes, glass fragments will scatter inside or outside the lamp box and

the gas charged inside the lamp will diffuse inside or outside the projector. The gas inside the lamp contains

mercury. Be careful not to breathe it or avoid it from entering your eye or mouth. If you should breathe it or if it

should enter your eye or mouth, see a doctor immediately.

In the event that the high-pressure mercury lamp exploded, glass fragments may have been scattered inside the

projector. Ask your dealer to replace the lamp and to inspect the inside of the projector. When you clean or replace

the lamp by yourself, be sure to hold the handle of the lamp. You may get injured by glass fragments.

When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the

projector or option lamp to prevent glass fragments from scattering.

Be sure to use the lamp exclusive to this projector, VLT-HC7000LP. Use of other lamps may cause a failure of the

projector.

•

Replacing the lamp

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi hc6500 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi hc6500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info