Bedienungsanleitung Mitsubishi HD5000A (Seite 5 von 24) (Englisch)

30512

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Device Selection Menu

This menu allows you to:

• Select the device for viewing on the display monitor.

• Select display monitor speakers or A/V Receiver

speakers for the audio.

• Change a NetCommand® compatible A/V Receiver’s

inputs automatically.

• Power NetCommand devices on or off.

• Verify NetCommand recordings and peer-to-peer

connections.

• Cancel recordings or peer-to-peer connections.

• Display the menu for HAVi devices.

Transport Menu

This menu allows you to operate the transport functions of

NetCommand compatible IR controlled and IEEE 

recording and playback devices.

Record and Connect Buttons

The Record button on the remote control will allow you

to begin a recording or schedule a delayed recording using

NetCommand. The CONNECT button allows you to

establish a peer-to-peer connection between two IEEE

 devices connected to the HDTV Receiver network.

Note: To the left is a list of devices by several

manufacturers that have been tested and shown to be

compatible with the NetCommand control system.

When you use these devices you will be able to control

them without changing the setting of the remote control

from Cable/DBS/DTV to another product. Since

similar devices from the same manufacturer often operate

the same way, other models may be compatible, however

they have not been tested so not all NetCommand

functions may be available. For devices that are not

supported by NetCommand, you will need to use that

device’s original remote control or program the HDTV

Receiver remote to operate these devices in the traditional

manner.

You need to program your HDTV Receiver

remote to operate the NetCommand features.

1. Move the slide switch at the top of the

Remote Control to the Cable/DBS/DTV

position.

2. Press and hold on the POWER button.

3. While holding on the POWER button,

enter the number for NetCommand 197.

4. Release the POWER button.

IMPORTANT

Track List

The Track List allows you to play, select or delete the

programs stored on your IEEE  AV Disc.

NetCommand® Setup

For NetCommand traditional devices, the NetCommand

Setup should have been completed. The NetCommand

Setup will detail what type and brand of devices are

connected and how these devices are connected to the

HDTV Receiver and A/V Receiver. In addition, you

need to connect IR Emitters to the HDTV Receiver

connection labeled IR Output NetCommand. IR

Emitter ends should be properly placed in front of each

NetCommand IR device. You will need to make this

connection in order to control NetCommand IR devices.

The remote control needs to be programmed to operate

NetCommand functions. See the HD- Owner’s Guide

for instructions on connecting IR compatible devices, using

the NetCommand Setup and programming the remote

control.

Non-NetCommand IR Devices

When you are using a non-NetCommand compatible

device, select the device on the Device Selection menu and

press ENT(er). Then move the slide switch at the top of

your remote control to the appropriate layer and point the

remote control at the device to control it, or you will need

to use the remote control that came with that device.

Special Features

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi HD5000A Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info