Bedienungsanleitung Mitsubishi HMS140VA (Seite 18 von 40) (Englisch)

604759

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Maintenance

The climate system’s safety valve (FL2) must be completely

sealed. Checks must be carried out regularly as follows:

■ Open the valve.

■ Check that water ows through the valve. If this does not

happen, replace the safety valve.

■ Close the valve again.

■ The heating system may need to be relled after checking

the safety valve, see the section “Filling the heating

system”.

Hot water heater safety valve

The water heater’s safety valve sometimes releases a little

water after hot water usage. This is because the cold water,

which enters the heater to replace the hot water, expands when

heated causing the pressure to rise and the safety valve to open.

Also check the water heater safety valve regularly. The

appearance and location of the safety valve differs between

different installations. Contact your installer for information.

Pressure gauge in indoor unit

The working range of the heating system is normally 0.5 – 1.5

bar when the system is closed. Check this on the pressure

gauge (BP5).

Emptying the hot water heater

The water heater is of the coil type and is drained using the

siphon principle. This can be done either via the drain valve on

the incoming cold water pipe or by inserting a hose into the

cold water connection.

Emptying the vessel

Contact your installer if the vessel in indoor unit needs

emptying.

Maintenance of outdoor unit

Outdoor unit is equipped with control and monitoring

equipment, however some exterior maintenance is still

necessary.

Make regular checks throughout the year that the inlet grille is

not clogged by leaves, snow or anything else. During the cold

months of the year, check to make sure that there isn’t a build up

of ice or frost under outdoor unit. Strong wind combined with

heavy snowfall can block the intake and exhaust air grilles.

Make sure that there is no snow on the grilles.

Also check that the condensation water drain under outdoor unit

is not blocked.

If necessary the outer casing can be cleaned using a damp

cloth. Care must be exercised so that the heat pump is not

scratched when cleaning. Avoid spraying water into the grilles

or the sides so that water penetrates into outdoor unit. Prevent

outdoor unit coming into contact with alkaline cleaning agents.

WARNING!

Rotating fan

Saving tips

Your Hydrolution produces heat and hot water according to

your needs. It also attempts to carry out all requirements with

all available “aids” from the control settings made.

The indoor temperature is naturally affected by the energy

consumption. Therefore, take care not to set a temperature

higher than necessary.

Other known factors that affect the energy consumption are,

for example, hot water consumption and the insulation level of

the house, as well as the level of comfort you require.

Also remember:

■ Open the thermostat valves completely (except in the

rooms that are to be kept cooler for various reasons, e.g.

bedrooms).

Thermostat valves in the radiators and floor loops can

negatively affect the energy consumption. They slow the ow

in the heating system, which the heat pump wants to

compensate with increased temperatures. It then works harder

and consumes more electrical energy.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi HMS140VA Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info