Bedienungsanleitung Mitsubishi HSHD2000U (Seite 40 von 80) (Englisch)

31038

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

When you program both the D-VHS and analog timer recording

When you turn the VCR off, the programmed recording light will appear on the front

panel display, showing that the VCR is in stand-by mode for the analog timer

recording. In this mode, the D-VHS timer recording you have set may not be

recorded depending on the integrated HDTV or IEEE 1394-equipped HDTV

receiver that you are using. (Refer to your TV or receiver owner’s guide for the

details.) If so, you need to press POWER on the VCR front panel once to cancel

the stand-by mode when the D-VHS timer recording is activated. When you press

POWER, the programmed recording light will be turned off but the VCR power will

remain off. Please note that the VCR cannot activate the analog timer recording

while the programmed recording light is turned off.

When the D-VHS timer recording is over, press POWER on the front panel twice to

turn on the programmed recording light.

Analog (S-VHS/S-VHS ET/VHS) Timer Recording

of Digital Broadcast

IMPORTANT

Be sure to connect the VCR and an integrated HDTV or an IEEE 1394-

equipped HDTV receiver with an S-video/video and an audio cable to record a

digital broadcast in analog format.

1 Select the Front S-input in the S-VHS Set-UP menu when you connect an

integrated HDTV or IEEE 1394-equipped HDTV receiver to the front panel of the

VCR, or Rear S-input when you connect an integrated HDTV or IEEE 1394-

equipped HDTV receiver to the rear of the VCR. See Selecting S-input

Setting on page 33.

2 Select the channel you would like to record on an integrated HDTV or an IEEE

1394-equipped HDTV receiver, not on the VCR.

3 Load a tape with its erasure prevention tab intact into the VCR.

4 Press MENU. VCR Main Menu appears on your screen. Turn the ADJUST

dial to select Program to record. Turn the SHUTTLE ring to the right.

If there is at least one programmed recording already entered, you will see the

Recap screen. Wait 4 seconds, and the VCR Plus+ system menu will appear.

IMPORTANT

If you have already programmed 8 recording events, Program memory is full

will appear on your screen for 3 seconds, and then the Recap screen will

appear. Use CANCEL to erase an entry before you can add another one.

5 VCR Plus+ system menu appears. See page 42 to learn how to program with

VCR Plus+ system. To pass this screen, turn the SHUTTLE ring to the right.

Timer Recording



ªVCR Main Menu

¬Program to record

ƒ1394 connection list

√Customize choices

»S-VHS Set-Up

ƒFirst Time Set-Up



Use ADJUST to select,

and ENTER.

Press MENU to exit menus



¬VCR Plus+ system



Use number keys to enter

the PlusCode number

--------



or press ENTER to

program.



Press MENU to go back.

¬Program to record

CH DAY ON OFF

10 TH15 9:00a10:30pSP

§--- -- --:-- --:-- SP

--- -- --:-- --:-- SP

ππππππππππππππππππππππππ

Use ADJUST to select,

and ENTER.

Press MENU to go back.

Recap screen

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi HSHD2000U Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info