Bedienungsanleitung Mitsubishi L75-A81 Laservue (Seite 63 von 100) (Englisch)

475237

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

6. NetCommand Control of an A/V Receiver 61

In the U.S. call 1(877) 675-2224 for assistance.

If using an optional audio cable between the TV and

A/V receiver, connect it.

Connect the IR emitter cable to the TV and position

the IR emitter where it can send signals to the A/V

receiver. See “IR Emitter Placement,” page 51.

Setup to Control Automatic Audio

and Video Switching via HDMI

When this setup is complete, the “learned” A/V receiver

input will appear in the TV’s Activity menu as a select-

able input.

Power on the A/V receiver.

Set the

TV’s remote control to

mode using the

side button.

Power on the TV.

When the

New Device Found screen displays,

select device name AVR if it is not recognized auto-

matically.

Navigate to the

Inputs > AVR menu or, from

within the New Device Found screen, highlight

NetCommand and press

ENTER

To set up A/V switching over HDMI, choose your

devices from a list. Unlike the device list described for

Case 2, this is a generic list containing more than just

the devices detected in your setup.

In the

Inputs > AVR > NEXT menu, press

to highlight the name of the A/V receiver input to

control. In this example, it is the DVD input.

Press

ENTER

on the TV’s remote control.

While the text

DVD is flashing, press and hold the

DVD INPUT

key on the A/V receiver’s remote control.

When a check appears next to

DVD, release the

DVD INPUT

key.

If the text stops flashing before the check mark •

appears, repeat this step.

To erase the IR code just “learned,” press •

CANCEL

while the name is highlighted.

If there are no more devices to set up, highlight

10.

EXIT and press

ENTER

or continue to set up addi-

tional A/V receiver audio/video sources.

Setting Up A/V Receiver Control, continued

NetCommand Control of a Device Con-

nected to an HDMI A/V Receiver

Use this setup to have NetCommand control a device

sending audio and video through the A/V receiver to the

TV via HDMI.

You must have already completed the procedure under

“Setup to Control Automatic Audio and Video Switching

via HDMI” on this page. That procedure placed an icon

in the Activity menu for the device (input) connected to

the A/V receiver.

HDMI

Cable

Any Connection

Type

Source

Device

A/V

Receiver

Set up NetCommand control of A/V receiver audio/

video switching via HDMI as described on this

page.

Press

BACK

to close any open menus and return to

normal TV viewing.

Press

ACTIVITY

Highlight the icon for the A/V receiver input you

wish to control.

Press

ENTER

to switch the TV to the A/V receiver

and the A/V receiver to the input.

Open the

Inputs > Learn menu.

Perform NetCommand “learning” for the con-

nected )device by following the steps in “Initial

NetCommand Setup,” page 52.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi L75-A81 Laservue Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info