Bedienungsanleitung Mitsubishi Lancer - 2014 (Seite 89 von 434) (Englisch)

617123

Zoom out

Zoom in

Vorherige Seite

1/434

Nächste Seite

Free-hand Advanced Security Transmitter (F.A.S.T.-key) (if so equipped)

5-22 Features and controls

5. While pushing the ignition switch from

“LOCK” (PUSH OFF) to “LOCK”

(PUSH ON), set the ignition switch to the

“ON” position and confirm that all warn-

ing lights and warning displays are oper-

ating properly.

6. Without pressing the accelerator pedal,

slowly turn the ignition switch to the

“START” position to start the engine.

Release the ignition switch when the

engine starts.

After several attempts, you may experience

that the engine still does not start.

1. Make sure that all electric devices, such

as lights, air conditioning blower and rear

window defogger, are turned off.

2. While depressing the brake pedal on vehi-

cles equipped with continuously variable

transmission (CVT) or Twin Clutch SST

or the clutch pedal on the vehicles

equipped with manual transaxle, press the

accelerator pedal halfway and hold it

there, then crank the engine. Release the

accelerator pedal, immediately after the

engine starts.

3. If the engine still will not start, the engine

could be flooded with too much gasoline.

While depressing the brake pedal on vehi-

cles equipped with CVT or Twin Clutch

SST or the clutch pedal on the vehicles

equipped with manual transaxle, push the

accelerator pedal all the way down and

hold it there, then crank the engine for 5

to 6 seconds. Return the ignition switch to

the “LOCK” position and release the

accelerator pedal. Wait a few seconds, and

then crank the engine again for 5 to 6 sec-

onds while depressing the brake pedal or

the clutch pedal, but do not push the

accelerator pedal. Release the ignition key

if the engine starts. If the engine fails to

start, repeat these procedures. If the

engine still will not start, contact your

local Mitsubishi Motors dealer or a repair

facility of your choice for assistance.

When the ambient temperature is -4°F

(-20°C) or lower on vehicles with CVT, or

-22°F (-30°C) or lower on vehicles with Twin

Clutch SST, it may not be possible to start

from a standstill even with the selector lever

(CVT) or the gearshift lever (Twin Clutch

SST) in the “D” (DRIVE) position.

This phenomenon occurs because the trans-

axle has not warmed up sufficiently; it does

not indicate a problem. If this occurs, place

the selector lever (CVT) or the gearshift lever

(Twin Clutch SST) in the “P” (PARK) posi-

tion and let the engine idle for at least 10 min-

utes.

The transaxle will warm up, and you will be

able to drive normally.

Do not leave the vehicle during warm-up

operation.

NOTE

 Minor noises may be heard on engine start-

up. These will disappear as the engine warms

up.

When the engine is hard to start

Startability of continuously variable

transmission (CVT) vehicles or Twin

Clutch SST vehicles at extremely cold

ambient temperature

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi Lancer - 2014 Seite 89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info