Bedienungsanleitung Mitsubishi SD206U (Seite 13 von 30) (Englisch)

493637

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

EN-13

ENGLISH

Basic operation

Power-on

1. Turn on the device connected to the projector first.

2. Plug the power cord in the wall outlet.

• The POWER indicator lights up.

• If the power cord is unplugged from the wall outlet before

the projector is cooled down completely after use, the

fans may start rotating when the power cord is plugged

in and the POWER button is pressed next time.

3. Press the POWER button on the control panel or the ON button

on the remote control.

• It may take about one minute for the lamp to light up.

• The lamp occasionally fails to light up. In this case, wait for

the re-try. Still fails after retry, try to light the lamp again. If

the temperature of lamp is high, wait a few minutes and try to

light the lamp again.

• After the POWER button is pressed, the image may flicker

before the lamp becomes stable. This is not a product mal-

function.

• Regardless of the setting of LAMP MODE in the INSTALLA-

TION menu, the STANDARD lamp mode is activated by

default whenever the projector is turned on.

Important:

• Do not cover the lens with the lens cap while the lamp is on.

• The projector starts warming up when the POWER button is

pressed. During the warm-up process, images may appear dark

and no commands are accepted. The projector cannot be turned

off within 60 seconds after the lamp is turned on.

• By blinking red, the STATUS indicator indicates that the lamp

should be replaced soon. Replace the lamp when the STATUS

indicator blinks red. (See page 23 and 26.)

• Images may not be projected with good quality in an extremely hot

or cold environment. (This is not a product malfunction.)

4. Adjust the focus by turning the focus ring.

5. Choose your desired external input source using the COM-

PUTER or VIDEO button.

• The input source is switched from VIDEO to COMPUTER at

the press of the COMPUTER button on the control panel.

• The input source is switched between VIDEO and S-VIDEO

at every press of the VIDEO button on the control panel.

• If you use a remote controller, press the VIDEO or S-VIDEO

button to directly switch to VIDEO or S-VIDEO.

• The projector automatically selects the appropriate signal

format. The selected signal format is displayed on the

screen.

• To avoid permanently imprinting a fixed image onto your pro-

jector, please do not display the same stationary images for

long period.

6. Adjust the image size by turning the zoom ring.

• If necessary, adjust the focus and zoom again.

• If you move the zoom, the screen will be out of focus. If this is

the case, adjust the focus again.

1, 2

3, 1, 2

Indicator

Condition

STATUS POWER REMARKS

Stand-by - Red -

Turn on process of the power - Blinking red

About 4

seconds

Turn on process of the lamp Blinking green Green

Can not turn

off about 60

seconds after

turning on.

When the lamp is on. Green Green -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi SD206U Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info