Bedienungsanleitung Mitsubishi SD206U (Seite 22 von 30) (Englisch)

493637

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

EN-22

Lamp replacement

When the lamp no longer functions, replace it with a new one.

Caution:

• Do not remove the lamp immediately after using the projector. You

may get burned because the lamp very hot after use.

• Before replacing the lamp, press the POWER button to turn off the

lamp and wait for two minutes for lamp to cool down. Unplug the

power cord from wall outlet and wait one hour for the lamp to cool

down completely.

• Do not remove the lamp except for replacement. Careless han-

dling can cause injury or fire.

• Do not touch the lamp directly. It may break and cause injury or

burn.

• Be sure not to drop the lamp lid screw into the projector. Also be

sure not to put metal or any flammable objects inside because it

may cause fire or electric shock. If any objects should fall inside,

unplug and contact your dealer.

• Install the lamp securely to prevent failure and fire.

• If the lamp should break, small glass fragments may fall out

through the grilles and some may remain inside of the projector or

the lamp box. When taking the lamp box out, be sure to turn over

the projector and hold the handle of the lamp box to avoid injury

due to the glass fragments.

• If the lamp should break, never shake the lamp box or hold it in

front of your face after removing it. The lass fragments may fall out

and cause injury to your eyes.

• When placing the projector upside down to replace the lamp or

conduct maintenance, ensure that the projector is securely placed

before working with it.

• Be sure to use the lamp exclusive to this projector, VLT-XD206LP.

Use of other lamps may cause a failure of the projector.

1. Reverse the projector gently.

2. Loosen the screws (a) using a Phillips

screwdriver (+), and remove the lamp

cover (b).

3. Loosen the screws (c) using a Phillips

screwdriver (+).

4. Pull up the handle.

5. Pull out the lamp box by the handle

while holding the projector.

• Pull the lamp box out of the projec-

tor slowly. If it is pulled out quickly,

the lamp may break scattering

glass fragments.

• Do not spill liquid on the removed

lamp box or do not place it near any

flammable object or where children

can reach to prevent injury or fire.

6. Load a new lamp box securely into the

projector in the right orientation.

7. Put the handle back to the original posi-

tion.

• Make sure that the handle is

locked.

8. Tighten up the screws (c) using a Phil-

lips screwdriver (+).

9. Tighten up the screw (a) using a Phillips

screwdriver (+) to secure the lamp

cover.

Reset of the lamp operation time

Plug in the power cord, and reset the lamp

operation time by keep pressing the W, X,

and POWER buttons on the control panel at

the same time about 5 seconds.

Important:

• Unless these three buttons are pressed

at the same time, the lamp operation time isn’t reset.

• Make sure that the STATUS indicator is lit once (red) and the lamp

operation time is reset successfully.

• The projector doesn’t turn on if the lamp cover isn’t attached

securely.

• Be sure to reset the lamp operation time whenever you replace the

lamp.

• Do not reset the lamp operation time unless you replace the lamp.

Caution:

• The lamp is fragile. If it is broken, be careful not to cut yourself with

glass fragments.

• Contact your dealer for a new lamp.

• The lamp in this product contains mercury. Please dispose of

properly.

Interval of lamp replacement

When the lamp operation time exceeds the time elapsed*1, the

POWER LED will light green and STATUS LED will blink red. In this

case, replace the lamp immediately

SD206U

*1 2850 Hours

*2 3000 Hours*3

The times above are when LAMP MODE of the INSTALLATION menu

is set to LOW. When it is set to STANDARD, this duration will be short-

ened.

*3 When LAMP MODE is set to STANDARD, the time elapsed until

the lamp shutdown will be shortened to 2000 hours.

Caution:

• This projector uses a lamp that contains mercury. Disposal of the

lamp or the projector with the lamp may be regulated due to envi-

ronmental considerations. For disposal or recycling information,

please contact your local authorities or the Electronic Industries

Alliance: www.eiae.org. (For US only).

(a)

(b)

(c)

(a)

(b)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi SD206U Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info