Bedienungsanleitung Mitsubishi SRK63ZM-S (Seite 15 von 34) (Englisch)

604721

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

–14–

Airflow direction adjustment

Adjusting airflow direction

■ Up/down direction can be adjusted with the AIRFLOW U/D (UP/DOWN) button on the remote control. Every time you press this

button the mode changes as follows:

Change on AIRFLOW (UP/DOWN) mode.

■ Left/right direction can be adjusted with the AIRFLOW L/R (LEFT/RIGHT) button on the remote control. Every time you press this

button the mode changes as follows:

Change on AIRFLOW (LEFT/RIGHT) mode.

MEMORY FLAP (FLAP OR LOUVER STOPPED)

When you press the AIRFLOW (U/D or L/R) button once while the flap or louver is operating,

it stops swinging at the position. Since this angle is memorized in the microcomputer, the flap

or louver will automatically be set at this angle when the next operation is started.

WARNING

• Do not expose directly to airflow from the air-conditioner for a long time.

CAUTION

• When in COOL or DRY operation, do not operate for a long period with the

airflow blowing straight down. Otherwise, condensation may appear on

the outlet grill and drip down.

• Do not try to adjust the flaps and louvers by hand, as the control angle may

change or the flap or louver may not be closed completely.

HEAT

(Horizontal

blowing)

(Slant forward

blowing)

COOL, DRY

• Recommended angle of the flap when

stopping

• When operation starts, the flap and louver direction is fixed at the horizontal / center position in order to avoid cold draft, and return

to the set the position that was set after the warm air supply is starting.

• The flap and louver direction will be controlled to the horizontal/center position when the room temperature reaches the set tem-

perature and compressor stops or when defrosting is in operation.

• The airflow direction cannot be set during the period mentioned above. Change the airflow direction settings after the warm air is

supplied and the flap/louver goes to the set position.

(Swing)

(Flap stopped)

(Louver stopped)

(Swing)

NOTE FOR HEATING OPERATION

• The actual position of the flap and louver may differ from the display shown.

NOTE

3D AUTO operation

■

Fan speed and air flow direction are automatically controlled, allowing the entire room to be efficiently conditioned.

Press the ON/OFF button.

Press the 3D AUTO button.

Each time the 3D AUTO button is pressed, the display is switched in the

order of:

(Normal operation)

(3D AUTO)

No display

• 3D AUTO operation is cancelled when you switch the operation mode.

• If 3D AUTO operation is cancelled then the air flow direction changes to

that used before 3D AUTO was set.

• 3D AUTO operation can be set in AUTO, COOL, or HEAT operation

mode only.

NOTE

Releasing procedure

Press the 3D AUTO button to turn off the 3D AUTO display.

RKW012A412D_EN_001-032 4/15/14, 13:5514

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi SRK63ZM-S Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi SRK63ZM-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info