Bedienungsanleitung Mitsubishi SRK71ZR-S (Seite 16 von 34) (Englisch)

587229

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

– 15 –

Airﬂ ow direction adjustment

■ Up/down direction can be adjusted with the AIRFLOW U/D (UP/DOWN) button on the remote control. Every time you press this button

the mode changes as follows:

Change on AIRFLOW (UP/DOWN) mode.

■ Left/right direction can be adjusted with the AIRFLOW L/R (LEFT/RIGHT) button on the remote control. Every time you press this

button the mode changes as follows:

Change on AIRFLOW (LEFT/RIGHT) mode.

MEMORY FLAP (FLAP OR LOUVER STOPPED)

When you press the AIRFLOW (U/D or L/R) button once while the ﬂ ap or louver is operating, it

stops swinging at the position. Since this angle is memorized in the microcomputer, the ﬂ ap or

louver will automatically be set at this angle when the next operation is started.

WARNING

• Do not expose directly to airﬂ ow from the air-conditioner for a long time.

CAUTION

• When in COOL or DRY operation, do not operate for a long period with the

airﬂ ow blowing straight down. Otherwise, condensation may appear on the

outlet grill and drip down.

• Do not try to adjust the ﬂ aps and louvers by hand, as the control angle may

change or the ﬂ ap or louver may not be closed completely.

HEAT

(Horizontal

blowing)

(Slant forward

blowing)

COOL, DRY

• Recommended angle of the flap when

stopping

• When operation starts, the ﬂ ap and louver direction is ﬁ xed at the horizontal / center position in order to avoid cold draft, and return

to the set the position that was set after the warm air supply is starting.

• The ﬂ ap and louver direction will be controlled to the horizontal/center position when the room temperature reaches the set

temperature and compressor stops or when defrosting is in operation.

• The airﬂ ow direction cannot be set during the period mentioned above. Change the airﬂ ow direction settings after the warm air is

supplied and the ﬂ ap/louver goes to the set position.

(Swing)

(Flap stopped)

(Louver stopped)

(Swing)

NOTE FOR HEATING OPERATION

• The actual position of the ﬂ ap and louver may differ from the display shown.

NOTE

3D AUTO operation

■ Fan speed and air ﬂ ow direction are automatically controlled, allowing the entire room to be efﬁ ciently conditioned.

Press the ON/OFF button.

Press the 3D AUTO button.

Each time the 3D AUTO button is pressed, the display is switched in the

order of:

(Normal operation)(3D AUTO)

No display

• 3D AUTO operation is canceled when you switch the operation mode.

• If 3D AUTO operation is cancelled then the air ﬂ ow direction changes to

that used before 3D AUTO was set.

• 3D AUTO operation can be set in AUTO, COOL, or HEAT operation mode

only.

NOTE

Releasing procedure

Press the 3D AUTO button to turn off the 3D AUTO display.

RLD012A002G_EN.indd 15RLD012A002G_EN.indd 15 2015/02/27 14:36:412015/02/27 14:36:41

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi SRK71ZR-S Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi SRK71ZR-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info