Bedienungsanleitung Mitsubishi WD-52725 (Seite 98 von 108) (Englisch)

475285

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

18. The sound does not match the screen picture. • NetCommand® is setup incorrectly.

• The TV’s “Listen to:” setting may be set to SAP.

• If using stereo or A/V receiver speakers, check their input selection.

• If using stereo or A/V receiver, check that AUDIO 2 of MONITOR

OUTPUT on TV’s back panel is connected to the A/V receiver.

19. There is a large black or gray rectangle on the

screen.

• The TV’s analog closed captioning has been set to “text” mode in

the Captions menu. Turn off because there is no text information

being broadcast.

20. You cannot see a picture when playing a VHS

tape.

• Display the Device Selection menu and select the correct VCR.

• Check your VCRs owner’s guide for further trouble shooting.

21. V-Chip is not working. • Make sure that V-Chip is On.

• If V-Chip Hours are currently set to disable the V-Chip lock, the

V-Chip will not block programming.

22. The TV will not turn on after being plugged in. • If green light on front panel is blinking, wait for at least one

minute for the light to turn off, then press Power again.

23. TV functions do not respond to the remote

control or to front panel control and will not

Power Off.

• Use the System Reset button as explained at the end of this

section.

24. Name options not available for some channels • Only memorized analog channels can be named.

25. When viewing a stopped VCR, white lines are

rolling on the screen.

• Turn off video mute for the VCR.

• Begin playing the tape.

• Change the VCR input to the antenna input.

26. TV turned itself Off and the light on the Front

Panel started to blink.

• Momentary power fluctuation caused the TV to turn off to prevent

damage. Wait for the green light to stop flashing and turn On again.

• If the TV does not stay turned On, use the System Reset

button. If this happens frequently, obtain an AC line power

conditioner/surge protector.

27. When a Device is selected from the Device

Selection menu, the screen is blue

(no signal source).

• Make sure the selected device is turned on.

• From the Edit NetCommand® menu select Review setting. Verify that

the inputs are actually connected to the TV . If they are not, either

change the physical connections on the back panel, or select the

Change setting on the Edit NetCommand menu to change the TV

NetCommand’s settings for the connection.

28. The Device does not respond to button presses

from the remote.

• Remote has not been setup for NetCommand

use.

• The incorrect manufacturer was selected during setup.

Select the Change setting from the Setup menu and then the device

to display the manufacturer selection. Change if necessary.

• The device is not supported and keys have not been learned.

• The requested function is not supported by NetCommand.

Verify that the function is supported or keys are learned.

• The IR emitter is incorrectly placed. Make sure the IR emitter is

facing the IR sensor in the device.

• The IR emitter is not plugged into the IR emitter Output

NetCommand.

• The IR emitter is facing the TV screen, causing double signals. Be

sure that the IR emitter cannot send to the TV.

29. The A/V Receiver is the selected audio source

but there is no sound.

• Check to see if the A/V Receiver power is turned on. After the power

is turned on, redisplay the Device Selection menu and press ENTER

to allow NetCommand to correctly select the A/V Receiver input.

• From the Setup Menu select Review setting. Check the Review

screen to see if the A/V Receiver inputs and device correspond to the

actual connections on the A/V Receiver. If they do not match, either

change the actual connections, or select Change on the Edit

NetCommand menu to change the device on the Connection screen.

Problem Possible Solution

Troubleshooting, continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-52725 Seite 98

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info