Bedienungsanleitung Mitsubishi WD-60638 (Seite 30 von 40) (Englisch)

475268

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

30 Appendices

For assistance call 1(800) 332-2119

Reset Name When to Use How to Use Resulting Action

Format If the picture shape

seems incorrect, use

the

FORMAT

key to

change the picture

shape.

Press

FORMAT

to cycle through the

available picture shapes for the

signal.

The last-used format for a signal

type will be recalled on the input.

Note: Also check the aspect ratio

feature on your cable box, satellite

receiver, or other device, as this may

be altering the picture.

Picture and

Sound Resets

(for the single

current input)

When audio and/

or video settings for

a single input seem

incorrect, use the reset

option to return the

input to the original

factory settings.

While viewing the input to reset, 1.

press

and go to Picture >

Reset or Sound > Reset.

Press 2.

ENTER

to reset.

All picture or sound settings for

the individual input are reset.

Channel Scan To erase and re-mem-

orize channels on the

antenna input. Use

after moving the TV to

a new area or reposi-

tioning the antenna.

Press 1.

and go to Channels

> Antenna Source.

Highlight the reception mode, 2.

either Cable or Air, and press

ENTER

Go to 3. Channels > Scan Channels

and start the channel scan. Be

sure Additive Scan is set to OFF.

All previously memorized chan-

nels for the antenna input are

erased and a new set of memo-

rized channels is created.

Locks Menu

To change your Locks

menu PIN

When prompted for the PIN, press

the number

and

LAST

keys on the

TV remote control at the same time.

To use number keys only, press

6 4 8 7

Allows establishment of a new

PIN.

TV Locks To temporarily disable

channel or ratings

locks.

Allows you to view a locked

channel or program. Turn the TV

off and then on to restore locks.

TV Re set Comparison Guide

You can resolve many common TV problems using the

reset functions described in the following table.

IMPORTANT

Before you change sound or picture settings: If

picture or sound settings seem wrong for a broadcast

channel (a channel from the

ANT

input, a cable box,

or satellite receiver), first check other channels from

the same input before changing settings. If most other

channels from the same input seem correct, there is

likely a problem with the broadcast rather than with the

TV. Use care in this case, as changes you make to fix

problems on individual channels also affect all other

channels on the same input.

Appendix B: Troubleshooting

Service and Customer Support

Service

If you are unable to correct a problem with your TV,

consult your Mitsubishi dealer or Mitsubishi Consumer

Relations at (800) 332-2119.

• DO NOT adjust any controls other than those

described in this Owner’s Guide.

• DO NOT remove the protective back cover of your

TV.

Customer Support

• To order replacement or additional remote controls

or lamp cart

ridges,

visit our website at www.mitsu-

parts.com or call (800) 553-7278.

• For questions:

Call Consumer Relations at 800-332-2119.

E-mail: MDEAservice@mdea.com

Website: www.mitsubishi-tv.com

Important

All lamps replaced under warranty must be returned to

Mitsubishi where they will be inspected to verify failure

defects.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-60638 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info