Bedienungsanleitung Mitsubishi WD-60735 (Seite 86 von 94) (Englisch)

475328

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

86 Appendices

Appendix F: Troubleshooting, continued

NetCommand IR Control

Symptom Remarks

1. Cannot see the menu from the A/V Receiver. A/V Receiver Set Up for Audio-Only Switching•

The A/V Receiver is not connected to any video input of

the TV. To check the A/V Receiver menu, temporarily plug

into an unused input of the TV, such as Input 3. Exit the

Auto Input Sensing screen and select Input 3 from the Input

Selection menu. Press MENU.

A/V Receiver Set Up for Audio and Video Switching over HDMI•

Use the MENU key on the A/V receiver’s remote control.

A/V Receiver with NetCommand for • HDMI.

Press INPUT to open the Input Selection menu. Highlight

the A/V receiver icon and press MENU.

2. NetCommand unable to learn specific device

keys.

A/V Device does not use IR format for remote control •

signal. ITT and RF formats cannot be learned.

Room lighting may affect the signal. Have the remotes very •

close (6 inches or less) to the TV during Learning.

If learning a Mitsubishi remote control, make sure slide •

switch is not set to TV position.

Some, but not all, device key functions can be learned by •

NetCommand. For example, POWER and PLAY may be

learned, but other functions may not.

The signal from the remote control may not be strong •

enough. Insert fresh batteries and try Learning again.

3. The A/V receiver is the selected audio source

but there is no sound.

A/V Receiver Set Up for Audio-Only Switching•

Check to see if the A/V Receiver power is turned on. -

With A/V receiver power turned on, redisplay the -

Input Selection menu and press ENTER to allow

NetCommand to correctly select the A/V Receiver

input.

Incorrect setup in the Inputs > AV Receiver menu. -

Check the device connection assigned in the AV

Receiver menu.

A/V Receiver Set Up for Audio and Video Switching over HDMI•

Check to see if the A/V Receiver power is turned on. -

If the device is connected only to the TV (e.g., on ANT1, -

ANT 2, or a front panel input), verify that the TV’s

AUDIO OUTPUT is connected to the A/V receiver.

The A/V receiver is not switching properly because -

you have not learned the inputs. See “Setting Up

NetCommand Control of an A/V Receiver,” page 58.

4. There is no sound from the A/V receiver

for my DVD player or other surround sound

device even though I learned the IR code for

the A/V receiver’s DVD input or other input.

(A/V Receiver Set Up for Audio-Only Switch-

ing)

NetCommand A/V receiver setup for the DVD player or digital

surround sound device or other device is not switching prop-

erly. See chapter 6, “NetCommand IR Control,” and perform

A/V receiver setup for a digital surround sound device as

described under “A/V Receiver Control: Automatic Audio

Switching,” page 59.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-60735 Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info