Bedienungsanleitung Mitsubishi WD-60737 (Seite 46 von 88) (Englisch)

475277

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

46 5. NetCommand IR Control (837 Series)

The NetCommand system uses emitters connected

to the

–

NetCommand Output

jack to control other

devices such as DVD players, cable boxes, satellite

receivers, and VCRs.

IR emitter cables are available for purchase from

Mitsubishi. Request either part number 242D483020

(two-ended cable) or part number 299P254020 (four-

ended cable).

Connect the plug end of the IR emitter cable to the

IR—NetCommand Output

jack on the TV back panel.

When the

New Device Found screen displays,

highlight EXIT and press

ENTER

The New Device Found screen displays when you

connect the IR emitter.

Position the emitter end with the emitter bulb facing

the device’s remote control sensor. The bulb emits

infrared light in a cone-shaped pattern. Place the

bulb far enough from the sensor to allow the cone

pattern to reach the sensor.

In some cases, the emitter works better facing

downward from the top of the device. Experiment

to find what works best.

Secure the emitter ends in place using double-

sided tape.

Place any unused ends behind the devices to

prevent stray signals from reaching the IR sensors.

HDMI

AVR

AUDIO

OUTPUT

Y/ VIDEO

INPUT 2

INPUT 1

DIGITAL

AUDIO

OUTPUT

DVI/PC

AUDIO

(480i / 480p / 720p / 1080i)

INPUT

AUDIO

Y/ VIDEO

GLASSES

EMITTER

ANT

IR-

NetCommand

Output

HDMI

IR-

NetCommand

Output

IR-

NetCommand

Output

TV Main

Panel

DIGITAL

SURROUND

A/V Receiver

Other A/V Device

Connecting IR–NetCommand Output

In front of a

single average-

sized device

On top of a single

tall device

In front, shared

by two average-

sized devices

IR sensor

In front of a single

average-sized device

On top of a single tall

device

In front, shared by two

average-sized devices

IR sensor

In front of a single

average-sized device

On top of a single

tall device

In front, shared by

two average-sized

devices

IR sensor

Place IR emitters so the signal can be “seen” by the IR

sensor on each device.

If You are Unable to Locate

a Device’s IR Sensor

The IR sensor is usually behind the plastic window •

of the front display panel. Using a flashlight, you

may be able to see it as a round or square cutout.

If you cannot see the sensor and the device’s •

Owner’s Guide does not specify the location, do

the following using the device’s remote control.

Starting at one end of the plastic window, hold 1.

the device’s remote control about one-half

inch from the front of the device and press the

POWER

key.

If the device does not respond, move the 2.

remote control one inch toward the center and

try again. Repeat until the device responds.

Repeat the previous steps starting at the other 3.

end of the window. The sensor will be between

these two points.

IMPORTANT

Position IR emitters so that each device’s

sensor “sees” the signal from only one emitter.

Otherwise, a device receiving signals from

multiple sources (remote controls, IR emitters)

may not respond at all.

IR Emitter Placement

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-60737 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info