Bedienungsanleitung Mitsubishi WD-62628 (Seite 32 von 124) (Englisch)

475319

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

32 Chapter 2. Connecting

Connecting the IR Emitter NetCommand

If a single emitter end can be placed in a

position that will operate more than one device,

do not use a separate emitter end for the

additional device. A single device receiving

remote control signals from too many emitters

or remote controls may not respond at all.

IMPORTANT

IR Emitter NetCommand®

Figure 15

An IR emitter cable is included with the TV.

The emitters connected to these jacks are used by the

NetCommand system and by TV Guide On Screen® to

control other devices such as VCRs, DVD players, Cable

boxes and Satellite receivers.

1. Connect the plug end of the supplied IR Emitter

Cable to either one of the IR Output NetCommand

jacks on the TV back panel.

2. Run the cable for each of the emitter ends under,

alongside, or over the top of each device to be

controlled to the area of the front where the remote

control sensor is located.

3. Place the emitter end in front of the remote control

sensor of the device to be controlled. The emitter

bulb should face the remote control sensor. This bulb

emits infrared light in a cone shaped pattern. The

bulb needs to be placed far enough from the remote

control sensor to allow the cone pattern to include

the sensor.

The remote control sensor is usually behind the

plastic window of the front display panel. It is

sometimes visible when you look through the display

plastic using a flashlight and is normally a round or

square cutout behind the plastic. If you cannot see

the sensor and the device’s Owner’s Guide does

not specify the location, you can find it by using the

device’s remote control.

a. Hold the remote about one-half inch from the

front of the device. Starting from one end of the

display window plastic, press the POWER button.

b. If the device does not respond, move the remote

control one inch toward the center and try again.

c. Repeat this until the device responds.

d. Note this location and then start over from the

other end of the display window plastic, repeating

until the device responds again.

The remote control sensor will be somewhere

between these two positions. This is usually

enough accuracy for the placement of the IR

emitters.

• Withsomedevices,theemitterworksbetterfacing

downward from the top of the device. Some

experimentation may be needed.

• Theemitterendbeingusedcanbesecuredinplace

using double stick tape.

• Ifyouarenotgoingto

be using all emitter ends, place

the unused ends behind the devices so that they

cannot send signals to the remote control sensors.

$0.10/&/5

:1C1SJQQJ

*/165





47*%&0

7*%&0

"6%*0

-&'5

.0/0

"6%*0

3*()5

%57$"#-&

7)'6)'



/FU$PNNBOE

*3&.*55&3

(-JOL

64&8*5)

$BCMF$"3%

"/5."*/"/5"69

%*(*5"-

463306/%

"73FDFJWFS

0UIFS"7EFWJDF









Figure 15. Connecting IR Emitter NetCommand

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-62628 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info