Bedienungsanleitung Mitsubishi WD-62628 (Seite 43 von 124) (Englisch)

475319

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Chapter 3. NetCommand Setup and Editing 43

NetCommand must be set up and the IR

emitters properly placed for your cable box

and VCR so the TV Guide On Screen system

can control these devices.

IMPORTANT

NetCommand

Initial Setup, continued

Device Setup Screen

Figure 4

If the devices connected to the TV are already in

NetCommand memory, you can quickly select them

at this screen. Press ADJUST or to move to each

device type. Press ADJUST or to select the

manufacturer. Select “Other” if the manufacturer is not

listed. Later, you can use the Change setting in the Edit

NetCommand menu to learn the remote control signals

for this device. Select “None” for device types that are

not connected.

For the A/V Receiver, if the manufacturer is not listed, you

cannot select “Other”. Instead, select “None”. Later, you

can use the “Add” feature in the NetCommand menu to

have the TV add and learn the remote control signals for

this device.

If you have a camcorder connected, check the

Camcorder box. NetCommand will not be able to

control it, but will reserve the front input to use with

the camcorder. Check the PC box if you have a PC

connected. After completing your choices, select Next>

and press ENTER.

Figure 4. Device Setup screen

Note: If you selected “Other” for any of the device

names, you can direct the TV to “Learn” the connected

device by following the Edit NetCommand instructions.

For many device types, non-listed models will operate in

the same way as the listed models and you can still use

the pre-loaded setting.

TV Guide On Screen® System Setup

Figure 5

The TV Guide On Screen option allows you to select

whether you want to enable the TV Guide On Screen

system and, if so, which devices to include. To receive

the correct program listings for your area, you will need to

enter your five-digit ZIP code.

You can select one over-the-air source and one cable

source for TV Guide On Screen. If, however, you have

multiple cable sources, the channel-number assignments

may not match up correctly. See the table below for the

preferred connection combinations.

If One Source Is:

The Other Source Can Be:

Ant-1 Air Ant-2 Air

Cable Box

Cable Card N/A

Ant-1 Channels via Cable N/A

Ant-2 Channels via Cable N/A

For detailed information on using the TV Guide On

Screen system, please see the separate TV Guide On

Screen Interactive Program Guide User’s Manual.

Figure 5. TV Guide On Screen

Note:

• InputstoTVGuideOnScreencaninclude:

- Only one over-the-air source

- Only one cable source

• AnantennainputisrequiredfordownloadingTV

Guide On Screen schedules. If your cable box is

connected using HDMI or IEEE-1394, you must also

connect an antenna input.

• IfyourcableboxisconnectedtoaComponentinput,

be sure the box is set to send analog channels as

480i. If this is not possible, add an antenna input.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-62628 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info