Bedienungsanleitung Mitsubishi WD-62628 (Seite 49 von 124) (Englisch)

475319

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Chapter 3. NetCommand Setup and Editing 49

[Device] Screen

Figure 17

If you selected “None” for a device type during initial

setup, you can later add a device with this screen. This

screen also opens when you select the Change option in

the Edit NetCommand screen.

The sample screens here show the choices for adding a

VCR; similar screens will appear for any satellite receiver,

DVD player, or cable box.

Figure 17. [Device] screen

Choose ONE of these options:

• Selectarecognizedmanufacturer.Themodel

number optimized for NetCommand will display at

the bottom of the screen. If a number follows the

manufacturer’s name, (example: Mitsubishi 1), this

indicates additional models are optimized for that

manufacturer. For many device types, non-listed

models will operate in the same way as the listed

models and you can still use the pre-loaded setting.

After selecting Next>, the screens that follow are: the

Name Screen (Figure 20), Connection screen (Figure

21) and specialized device screens (Figures 22-24),

ending with the Finish screen (Figure 27).

• Select“Other,”thenhighlight“Learn”andpress

ENTER. This will allow you to have NetCommand

learn the remote control signals of this new device.

After selecting “Learn” and pressing ENTER, the

screens that follow are: [Device] Learn screen (Figure

18), [Device] Advanced Learn screen (Figure 19),

Name screen (Figure 20), Connection screen, (Figure

21) and specialized device screens (Figures 22-24),

ending with the Finish screen (Figure 27).

Edit NetCommand®: Add Devices, continued

• Select“Other”,skipLearnandselectNext>. This

will allow the device to appear and will allow

NetCommand to switch inputs to use this device.

However, NetCommand will not be able to control this

device. Later you may use the “Change” option in the

Setup menu to learn the remote control signals.

After selecting Next>, the screens that follow are: the

Name Screen (Figure 20), Connection screen (Figure

21) and specialized device screens (Figures 22-24),

ending with the Finish screen (Figure 27).

[Device] Learn Screen

Figure 18

Shown only if “Learn” was selected

1. Press ADJUST to select the check box for

each function to be learned.

2. Press ENTER and the function name will begin to

flash to confirm the ready-to-learn status.

3. Press the button on the device’s remote control that

corresponds to the selected function. A check mark

will appear and the function name will stop flashing.

This confirms the signal learned status.

4. To test the learned command, press the ENTER

button on the TV remote while the learned function

is still highlighted. The device should perform the

selected function. The device needs to be turned on

and the IR emitters properly placed for the test to be

successful (see page 32 for IR emitter placement).

5. Repeat for each function to be learned.

6. To erase a learned function, highlight the check box

for that function and press CANCEL.

7. When the function signals have been learned, press

ADJUST to select Next> and move to the [Device]

Advanced Learn screen.

NOTE: When learning the device’s remote control

signals, point the device’s remote control at the TV

screen.

Hint: If the device’s remote control uses a single button

for both Power On and Power Off, don’t learn the Power

Off function.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-62628 Seite 49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info