Bedienungsanleitung Mitsubishi WD-62628 (Seite 54 von 124) (Englisch)

475319

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

54 Chapter 3. NetCommand Setup and Editing

Adding IEEE 1394 Devices Automatically

Name for 1394 Device Screen

Figure 29

If you choose to add the discovered IEEE 1394 device,

the Name for 1394 Device screen appears. Enter a new

name for the device or use the default name that appears

automatically. The name used in this screen is the name

that appears in the Device Selection menu.

The DV option applies only to digital camcorders at

this time and is typically detected automatically by the

TV. If your camcorder uses DV formatting but the box is

unchecked, add the check mark manually.

To use the analog capability of some IEEE 1394 devices,

such as some DVCRs and cable boxes, check the Analog

Connection box.

• SomeDVCRs,forexample,canrecordandplay

as VHS or S-VHS in addition to D-VHS. This

allows you to play analog rental tapes or analog

tapes from your established library or to make

analog recordings from an antenna or cable

system.

• SomecableboxeswithIEEE1394connections

require an analog connection for on-screen

guides and emergency notices.

Note: You never need to check both the DV and Analog

Connection check boxes for a device.

Figure 29. Name for 1394 Device screen

Adding IEEE 1394 Devices

Automatically

Addition of IEEE 1394 devices is a special case of

NetCommand setup because the devices are detected

automatically. You review, edit, and delete these devices

through NetCommand just as you would any other

devices.

When you connect an IEEE 1394 device to the TV network

and power it on, the new device automatically announces

its presence. This process is called device discovery and

can take up to one minute.

Some non-audio/video or incompatible IEEE 1394 devices,

such as personal computers (PCs), may not announce

their presence to the TV. The TV is not able to show these

devices in the Device Selection menu. They can, however,

coexist and are still available to other devices on the IEEE

1394 network that are compatible with these non-audio/

video devices.

Try using the Cable/SAT/DTV position of the TV remote

control to see if it can control operation of IEEE 1394

cable boxes and satellite receivers. If not, use the remote

control that came with the device.

New 1394 Device Screen

Figure 28

When your TV discovers a new IEEE 1394 device, the

New 1394 Device screen appears. Select “Add” or “Do

Not Add” depending on whether or not you want the

device added to the Device Selection menu. If the IEEE

1394 device does not provide audio and video, you may

not want to add that device to the TV’s Device Selection

menu. Devices that were discovered but not added to

the Device Selection menu will still be listed in the Review

screen of the Edit NetCommand

menu.

Figure 28. New 1394 Device screen

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-62628 Seite 54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info