Bedienungsanleitung Mitsubishi WD-62725 (Seite 27 von 108) (Englisch)

475287

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

Connecting the IR Emitter NetCommand

IR EMITTER

NetCommand

DTV/

CABLE/

VHF/

UHF

ANT-1

MAIN

DVI

Analog Audio

TV back panel

(section detail)

A/V Receiver

Other A/V device

Figure 17. Connecting IR Emitter NetCommand

IR Emitter NetCommand®

Figure 17

A quadruple IR Emitter cable is included with the TV.

The emitters connected to these jacks are used by the

NetCommand system to control other devices such as

VCRs, DVD players, Cable boxes and Satellite receivers.

1. Connect the plug end of the supplied quadruple

IR Emitter Cable to one of the IR Output

NetCommand jacks on the TV back panel.

2. Run the cable for each of the emitter ends under,

along side or over the top of each device to be

controlled to the area of the front where the remote

control sensor is located.

3. Place the emitter end in front of the remote control

sensor of the device to be controlled. The emitter

bulb should face the remote control sensor. This

bulb emits infrared light in a cone shaped pattern.

The bulb needs to be placed far enough from the

remote control sensor to allow the cone pattern to

include the sensor.

The remote control sensor is usually behind the

plastic window of the front display panel. It is

sometimes visible when you look through the display

plastic using a flashlight and is normally a round or

square cutout behind the plastic. If you cannot see

the sensor and the device’s Owner’s Guide does

not specify the location, you can find it by using the

device’s remote control. Hold the remote about 1/2

inch from the front of the device. Starting from one

end of the display window plastic, press the POWER

button.

If the device does not respond, move the remote

control 1 inch toward the center and try again.

Repeat this until the device responds. Note this

location then start over from the other end of the

display window plastic, repeating until the device

responds again. The remote control sensor will be

somewhere between these two positions. This is

usually enough accuracy for the placement of the IR

emitters.

4. With some devices, the emitter will work better

facing downward from the top of the device.

Some experimentation may be needed.

5. The emitter end being used can be secured in

place using double stick tape.

If a single emitter end can be placed in a

position that will operate more than one device,

do not use a separate emitter end for the

additional device. A single device receiving

remote control signals from too many emitters

or remote controls may not respond at all.

IMPORTANT

6. If you are not going to

be using all emitter ends,

place the unused ends behind the devices so that

they cannot send signals to the remote control

sensors.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-62725 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info