Bedienungsanleitung Mitsubishi WD-62725 (Seite 99 von 108) (Englisch)

475287

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

30. The TV Speaker icon or A/V Receiver icon is

grayed out and not selectable.

• Select the Change setting from the Edit NetCommand menu, and

then select the device (for example VCR). Once the Connection

screen is displayed, check if the audio checkbox is selected for the

TV input and/or AVR input.

31. Devices are grayed out in the Device Selection

menu or the PIP Selection menu.

• A recording is in progress requiring the use of Monitor Out. Cancel

the recording to select the device.

• Digital channels and media cards cannot display in the PIP or POP.

32. Cannot see the A/V Receiver menu. • The A/V Receiver is not connected to any input of the TV. To check

the A/V Receiver menu temporarily plug into an unused input of the

TV. Then select Review from the Setup Menu, turn the input On to

view the A/V Receiver menu.

33. Screen is black when trying to view digital

channels or IEEE 1394 device.

• The PerfectColor™ color balance has been incorrectly set. Use the

Advanced menu to reset the color balance.

34. The REC button is not working, or, on the

Transport menu the record key is grayed out and

not available.

• The device does not support recording, such as a DVD player.

• Recordings can not be initiated from the Transport menu when

using an IEEE 1394 device. Press REC instead. The Record

menu displays allowing setup of a recording.

35. A program recorded on your TV is distorted

when played on a 4:3 TV.

• TV was set to Anamorphic when program was recorded.

Record programs in Cropped mode if playing back on a 4:3 TV.

36. Excessive digital artifacts. • The IEEE 1394 cable is too long (15 feet between devices is the

maximum length).

• There may be a slow device in the middle of the IEEE 1394 network.

Move the slow devices to the end so that connections for faster

devices do not pass through them.

37. Cannot see a picture from a DV Camcorder. • Go to Device Selection menu and select analog connection.

• Connect the DV Camcorder to analog input (for example, Input-3).

Select Setup from the main menu, then Change. At the Change

screen, select the camcorder. On the Name screen, check Analog

Connection. Select the device and on the following screen, select

which analog input was used, and check audio and/or video.

38. DVCR analog/digital problems. • If the tape is currently playing but no picture displays, there may be a

mismatch of the media with the display. Press DEVICE to

display the Device Selection menu. Press ENTER for the DVCR

device. If digital is selected, try analog, or if analog is selected, try

digital.

39. D-VHS recordings for digital cable have drop-

outs (loss of picture or sound), or no playback.

• Digital cable signals on IEEE 1394 can exceed the data rate

standards supported by DVCR.

40. There is no audio and video from the IEEE 1394

device.

• The device is not turned on - turn the device power on.

• No media (tape or disc) is inserted into the device.

• The media is blank (has no recording).

• The play command failed - Try pressing play again on the device’s

remote control or front panel.

• The device is already in use (for example: the device is currently

recording).

• The source is copy-protected or violates copy protection.

• The device’s digital video signal is not supported by the TV, such as

DV video, common with camcorders. Use analog connections

instead, if available.

• The device is not an audio/video device.

• Too many other devices are already communicating over

IEEE 1394. Remove or stop some devices and try again.

41. The IEEE 1394 Device is not listed in the Device

Selection menu.

• The device is unchecked in the Review screen. Select the

NetCommand menu. Through Review, verify the device is checked.

• The IEEE 1394 plug is disconnected or loose.

• The IEEE 1394 Device has not been powered On. Turn on.

• The device has not been discovered.

• The device is not an Audio/Video device

Problem Possible Solution

Troubleshooting, continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-62725 Seite 99

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info