Bedienungsanleitung Mitsubishi WD-62927 (Seite 117 von 128) (Englisch)

475281

117

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Appendices 117

Picture

Symptom Remarks

1. PIP does not display a picture.

• MakesuretheV-Chiplockisoff.

• NotallinputscanbedisplayedasaPIP.

2. CableCARD channel is not shown as PIP image

when CableCARD channel is the main image.

Due to the limitations of unidirectional CableCARD service, only one

scrambled CableCARD channel can be tuned, viewed, or recorded at a

time.

3. There is a large black or gray rectangle on the

screen.

The TV’s analog closed captioning has been set to “text” mode in the

Captions menu. Turn off because there is no text information being

broadcast.

4. You cannot see a picture when playing a VHS

tape.

• DisplaytheDeviceSelectionmenuandselectthecorrectVCR.

• CheckyourVCR’sowner’sguideforfurthertroubleshooting.

5. When viewing a stopped VCR, white lines are

rolling on the screen.

• TurnoffvideomutefortheVCR.

• Beginplayingthetape.

• ChangetheVCRinputtotheantennainput.

6. Screen is black when trying to view digital

channels or IEEE 1394 device.

The PerfectColor™ color balance has been incorrectly set. Press VIDEO

repeatedly until you see the PerfectColor option and press ENTER.

7. A program recorded on your widescreen TV is

distorted when played on a 4:3 TV.

TV was set to Anamorphic when program was recorded. Record

programs in Cropped mode if playing back on a 4:3 TV. Open the

Record menu and select Cropped before making such a recording.

8. Cannot see a picture from a DV Camcorder. DV formatting was not detected during automatic discovery, so you must

specify it manually. Open the Edit NetCommand screen, select Change,

then select the camcorder, Add, and in the Name for 1394 Device

screen, check mark the DV box.

9. DVCR analog/digital problems. If the tape is currently playing but no picture displays, there may be a

mismatch of the media with the display. Press DEVICE to display the

Device Selection menu. Press ENTER for the DVCR device. If digital is

selected, try analog, or if analog is selected, try digital.

Indicators

Symptom Remarks

1. Lamp indicator light is a constant red. Turn the TV off for at least 2 minutes. Turn back on. If light is still red,

the lamp has failed. Replace it. See Appendix G for lamp replacement

information.

2. Lamp indicator light is a constant yellow. Lamp may fail soon. Purchase a new lamp. See Appendix G for lamp

replacement information.

3. Lamp indicator light is a flashing yellow. Lamp cover door is open or lamp cartridge is not secure. See Appendix

G for lamp replacement information.

4. Status indicator light is a constant yellow. Room temperature has exceeded proper levels. Cool the room.

5. Status indicator light is a constant/flashing red. Service is required. Contact your dealer or a Mitsubishi Authorized

Service Center to arrange for a service evaluation. Listings of Mitsubishi

Authorized Service locations can be obtained from our web site, www.

mitsubishi-tv.com or by calling 1-800-332-2119.

Appendix J: Troubleshooting, continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-62927 Seite 117

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info