Bedienungsanleitung Mitsubishi WD-65837 (Seite 52 von 88) (Englisch)

475272

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

52 6. NetCommand Control of an A/V Receiver (837 Series)

IMPORTANT

To hear audio sent from the TV to the A/V receiver,

you must have:

Physically connected the TV to the A/V receiver •

via the analog or digital audio output.

Assigned, if needed, the name AVR if using an •

HDMI A/V receiver.

“•

Learned” the IR codes for the A/V receiver

inputs.

Assigned the TV’s audio output to the correct •

input in the NetCommand Inputs > AVR menu.

Selected the A/V receiver as the audio source. •

Press MORE then 9 (AUDIO), then

to show

the Speakers option,

then

to select the A/V

Receiver.

Setting Up A/V Receiver Control

Power and Volume

Perform this setup to control the A/V receiver power

and volume with the TV’s remote control.

To perform this setup you need:

The remote controls for both the TV and the •

A/V receiver.

An IR emitter cable available from Mitsubishi.•

Before You Begin

Connect your A/V receiver to the TV and any addi-

tional devices. See “Setting Up TV Inputs,” page 10

and “TV Connections,” page 14.

Connect the IR emitter cable to the TV and position

the IR emitter where it can send signals to the A/V

receiver. See “IR Emitter Placement,” page 46.

Set the

TV’s remote control to

mode using the

side button.

Setup to Control A/V Receiver Power and Volume

Open the

Inputs > AVR screen in one of two ways:

If using the • New Device Found screen for the

A/V receiver, highlight NetCommand and press

ENTER

to open the AVR screen.

If performing NetCommand setup at any time •

after Auto Sensing:

Press

, highlight Inputs, and highlight AVR

to open the AVR menu.

The first function highlighted in the

AVR screen is

always Power. Aim the TV’s remote control at the

TV and press

ENTER

to begin learning for Power.

Inputs > AVR screen. Perform

NetCommand IR “learning” for A/V

receiver power and volume keys.

When the

Power text starts flashing, aim the A/V

receiver’s remote control at the TV and hold the

POWER

POWER ON

key until a check mark appears

next to Power.

If the text stops flashing before the check mark •

appears, repeat this step.

To remove the key from NetCommand control, •

press the

CANCEL

key while the key name is

highlighted.

Press the 4. key on the TV’s remote control to highlight

other keys in the list. Repeat steps 2 and 3 for each addi-

tional function you wish to control through NetCommand.

If the A/V receiver has a separate

POWER OFF

key,

press on the TV’s remote to highlight Power Off.

Repeat steps 2 and 3 to “learn” the

POWER OFF

key.

If the device has no

POWER OFF

key, skip this step.

When finished “learning” the power and volume

keys, either

To watch TV, press •

BACK

To continue with NetCommand setup to control •

switching of A/V receiver inputs, highlight

NEXT and press

ENTER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-65837 Seite 52

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info