Bedienungsanleitung Mitsubishi WD-65838 (Seite 66 von 110) (Englisch)

475259

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

66 5. NetCommand IR Control (838 Series)

For assistance call 1(800) 332-2119

Initial NetCommand Setup

To perform this procedure, you need:

• The remote controls for both the TV and the

device you want to control.

• An IR emitter cable available from Mitsubishi

Note: To set up an A/V receiver, see “Setting Up A/V

Receiver Control,” page 71.

Connect and position the IR emitters for the

devices you wish to control. See “IR Emitters” on

the previous page.

Set the TV’s remote control to

mode and power

on the TV.

NetCommand Setup

NetCommand and Device-Specific Keys

Device-specific keys are those which have no

equivalent on the TV’s remote control. Use any of

these methods to set up NetCommand control for

these keys.

• TOOLS Menu. In some cases, the TV will, by

default, assign a key to the TOOLS menu. See

the table below.

Examples of Default NetCommand

Assignments in the TOOLS Menu

Cable Box, Sat-

ellite Receiver

ON DEMAND

DVD, DVR,

Blu-ray

SETUP

TOP MENU

ANGLE

VCR 3

INPUT

A/V Receiver 3

SURROUND

NetCommand’s default setup assigns some

device-specific keys to the TOOLS menu when

“learned.” These key functions are accessible only

with the

TOOLS

key.

•

Keys. There are four

keys,

through

which you can assign to any function on the

device’s remote control. For a cable box,

“learn” the

keys as the

A, B, C, D

keys.

• Arbitrary Key Assignment. You can assign a

device key arbitrarily to any “unlearned” key

on the TV’s remote control. Make a note of the

key name and function for later reference.

Switch the TV to the desired input to control. Press

INPUT

, highlight the input icon, and press

ENTER

Open the NetCommand Inputs > Learn menu.

The first function highlighted in the Learn screen

is always Power On. Aim the TV’s remote control

at the TV and press

ENTER

to begin learning for that

function.

When the

Power On

text starts flashing, aim the

device’s

remote control at the TV and hold the

POWER

key until a check mark appears next to Power On.

• If the text stops flashing before the check mark

appears, repeat the previous step.

• To remove the key from NetCommand control,

press the

CANCEL

key while the key name is

highlighted.

• To verify the device’s response to the IR code,

press

ENTER

to send out the code.

Inputs > Learn screen. Key names marked with a check

have been “learned.”

Some device-specific keys, such as

, are available

only from the TOOLS menu after “learning.”

Use navigation keys on the TV’s remote control to

highlight other keys on the list. Repeat steps 5 and

6 for each additional function you wish to control

through NetCommand.

If the device has a separate

POWER OFF

key, use

navigation keys on the TV’s remote to highlight

Power Off.

Repeat the earlier steps to “learn” the

POWER OFF

key.

If the device has no

POWER OFF

key, skip this step.

Press

EXIT

to finish NetCommand “learning” for the

current device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-65838 Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info