Bedienungsanleitung Mitsubishi WD-65838 (Seite 73 von 110) (Englisch)

475259

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

6. NetCommand Control of an A/V Receiver (838 Series) 73

For assistance call 1(800) 332-2119

Before You Begin

To complete these steps you will need:

• The remote controls for both the TV and the

A/V receiver.

• An IR emitter cable available from Mitsubishi.

• An HDMI-to-HDMI cable to connect the A/V

receiver to the TV and cables necessary to

connect devices to the A/V receiver.

Connect the A/V receiver to the TV with an HDMI-

to-HDMI cable. Do not connect the optional audio

cable at this time.

If desired, enable HDMI Control of a CEC-enabled

A/V receiver. See Appendix C, “HDMI Control of

CEC Devices.”

Connect your audio/video devices to the A/V

receiver. Note the name of the device connected

Pb Pr

INPUT 2

INPUT 1

DIGITAL

AUDIO

OUTPUT

(480i / 480p / 720p / 1080i)

Y/ VIDEO

Pb Pr

Y/ VIDEO

DVI/PC

LR INPUT

AUDIO

GLASSES

EMITTER

ANT

AUDIO

LAN

DIGITAL

AUDIO

OUTPUT

HDMI

HDMI cable

DIGITAL

AUDIO

OUTPUT

AUDIO

OUTPUT

AUDIO

OUTPUT

HDMI OUT

DIGITAL

AUDIO IN

ANALOG AUDIO IN

High-deﬁnition

DVD player

Cable box

VCR

Y/ VIDEO

A/V receiver with

HDMI output

Any connection

types

Optional

analog or

digital audio

connection

Multiple video inputs through a single HDMI cable. The

optional audio connection allows you to hear, through the

A/V receiver, devices connected to the TV only, e.g., an

antenna on the

ANT

input.

to each A/V receiver input. This information will be

needed later to set up NetCommand’s automatic

input switching.

If using an optional audio cable between the TV

and A/V receiver, connect it. Set up NetCommand

control of the A/V receiver’s TV audio input when

setting up automatic switching in the next procedure.

Connect the IR emitter cable to the TV and position

the IR emitter where it can send signals to the A/V

receiver. See “IR Emitters,” page 65.

Setup to Control Automatic Audio

and Video Switching via HDMI

When this setup is complete, the “learned” A/V receiver

input will appear in the TV’s Input Selection menu as a

selectable input.

Set the TV’s remote control to TV mode.

Navigate to the Inputs > AVR menu.

To set up A/V switching over HDMI, choose your A/V

receiver input from a list.

In the Inputs > AVR menu, highlight the name of the

A/V receiver input to control. In this example, it is

the DVD input.

Press

ENTER

on the TV’s remote control.

While the text DVD is flashing, press and hold the

DVD INPUT

key on the A/V receiver’s remote control.

When a check appears next to DVD, release the

DVD INPUT

key.

• If the text stops flashing before the check mark

appears, repeat this step.

• To erase the IR code just “learned,” press

CANCEL

while the name is highlighted.

If using an optional audio cable between the TV and

A/V receiver, “learn” the

TV AUDIO OUT

key to enable

automatic switching of audio from sources con-

nected to the TV only.

If there are no more devices to set up, highlight

EXIT and press

ENTER

or continue to set up addi-

tional A/V receiver audio/video sources.

Setting Up A/V Receiver Control, continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-65838 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info