Bedienungsanleitung Mitsubishi WD-65C9 (Seite 20 von 88) (Englisch)

475275

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

20 2. TV Connections

A/V Receiver

Most setups require either a digital audio cable or

analog stereo audio cables. To send audio from TV

channels received on the

ANT

input or devices con-

nected directly to the TV, you must use one of the

connections shown below. Usually, only one of these

connections is required.

The TV makes all audio available in digital and analog

formats:

Analog audio coming into the TV is available as •

output in digital stereo format on the

DIGITAL

AUDIO OUTPUT

jack.

Digital incoming audio is available as analog output •

on the

AVR AUDIO OUTPUT L

and

jacks.

HDMI

AVR

AUDIO

OUTPUT

Y/ VIDEO

INPUT 2

INPUT 1

DIGITAL

AUDIO

OUTPUT

DVI/PC

AUDIO

(480i / 480p / 720p / 1080i)

INPUT

AUDIO

Y/ VIDEO

GLASSES

EMITTER

ANT

RS-232C

IR-

NetCommand

Output

DIGITAL

AUDIO

OUTPUT

COAXIAL

INPUT

OPTICAL

INPUT

COAXIAL

INPUT

AVR

AUDIO

OUTPUT

DIGITAL

AUDIO

OUTPUT

Digital coaxial cable

(for a digital A/V

receiver)

Stereo analog

cables

(for an analog

A/V receiver)

TV main panel

A/V receiver back panel

Note:

On rare occasions, an HDMI signal may be •

copy-restricted and cannot be output from

the TV as a digital signal. To hear these copy-

protected signals through the A/V receiver, use

the connection for an analog A/V receiver.

Check the A/V receiver’s Owner’s Guide for •

information concerning use of the digital input

and switching between digital sound and

analog stereo sound from the TV.

A/V Receiver with HDMI Output

Required: One HDMI-to-HDMI cable

This option allows you to view content from devices

connected to an A/V receiver. The A/V receiver can

send audio and video to the TV over a single HDMI

cable. You can use an HDMI connection as described

here in addition to an audio connection from the TV’s

audio output. The optional audio connection allows you

to hear, through the A/V receiver, devices connected to

the TV only, e.g., an antenna on the

ANT

input.

You may be able to use the TV’s remote control (in

mode) to operate connected CEC-enabled HDMI

devices. Experiment with your equipment to determine

which functions are available to the TV’s remote control.

See Appendix C, page 67.

837 Series:

This setup allows you to use NetCom-

mand-controlled audio and video switching over the

HDMI cable. See “Case 3: Automatic Audio and Video

Switching via HDMI” on page 55.

To use NetCommand to supplement HDMI control of a

CEC-enabled A/V receiver, note the recommendations

under “More About Using an HDMI Connection,” page 55.

HDMI

AVR

AUDIO

OUTPUT

Y/ VIDEO

INPUT 2

INPUT 1

DIGITAL

AUDIO

OUTPUT

DVI/PC

AUDIO

(480i / 480p / 720p / 1080i)

INPUT

AUDIO

Y/ VIDEO

GLASSES

EMITTER

ANT

IR-

NetCommand

Output

DIGITAL

AUDIO

OUTPUT

HDMI OUT

DIGITAL

AUDIO

L R

High-deﬁnition

DVD player

Cable box

VCR

HDMI

AVR

AUDIO

OUTPUT

DIGITAL

AUDIO

OUTPUT

A/V receiver

with HDMI

output

Optional analog or

digital audio

connection

TV main panel

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-65C9 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info