Bedienungsanleitung Mitsubishi WD-73735 (Seite 82 von 94) (Englisch)

475330

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

82 Appendices

General TV Operation

Symptom Remarks

1. A fan is running even while the TV is powered

off.

The room is too warm. When the TV is off, internal components

continue to draw power and must be cooled by the fan.

The fan gets louder after the TV is shut off.

Normal operation. The fan speeds up to cool the lamp quickly

after the TV has been shut off.

The TV remote control does not work. Check that the batteries are fresh and installed correctly.•

Check that the slide switch on the remote is set to TV.•

Be no more than 20 feet from the TV when using the remote control.•

Program the remote control to operate the TV or other device.•

Reset the remote control.•

If you have a custom home theater controller but prefer to use •

the TV’s remote control, unplug the controller cable from the

TV’s IR—NetCommand® Output/External Controller Input.

When I try to use the remote control, the

POWER key blinks five times.

Replace the batteries.

TV does not respond to the remote control or

to control-panel buttons and TV will not power

on or off.

Unplug the AC power cord for 10 seconds.•

Use the System Reset button.•

When a device is selected from the Input Selec-

tion menu, the screen is blue or black (no signal

source).

• Makesuretheselecteddeviceisturnedon.

• Beginplayofthedevice.

You have forgotten your Lock menu pass code. See Appendix B, “Bypassing the Parental Lock,” page 65.

Rating restrictions are not working.

Open the Parental Lock menu and:

• VerifythattheU.S.RatingsorOtherRatingssettingisOn.

• ChecktheLockTime/UnlockTimetocheckifratingrestric-

tions are disabled.

• RatingrestrictionsapplyonlytocontentonANT1andANT2,

and VIDEO composite video jacks.

On-screen displays appear each time you

change a function.

Normal TV operation.

10. A warning message appeared on screen

stating, “TV will shut down in a few seconds.

Please check if the air flow is blocked.”

• Roomtemperaturehasexceededproperlevels.Coolthe

room.

• TheTVhasoverheated.Clearblockedairventsandensure

at least four inches of clearance on all sides of the TV.

• CleantheairfilteronthelampcartridgeSeepage75.

11.

I have turned on CEC for my HDMI devices but

control is erratic and I wish to disable it.

Turn off all NetCommand HDMI control signals from the TV. Open the •

Inputs > NetCommand HDMI Control menu and set to Off (page 48).

Turn off the TV’s NetCommand HDMI control for the specific •

device. Open the Inputs > Name menu, select the device, select

Control Off (page 48).

Disable CEC on the device itself. See the device’s instructions.•

If the problem persists, do the following:•

Disconnect the device from the TV.1.

Open the Inputs > Name menu. Highlight the device and 2.

select Delete to remove the device from the Input Selection

menu.

Reconnect the device to the TV and Auto Input Sensing will 3.

recognize the device as a non-CEC device.

Appendix F: Troubleshooting, continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-73735 Seite 82

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info