Bedienungsanleitung Mitsubishi WD-73827 (Seite 59 von 128) (Englisch)

475282

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Chapter 4. Netcommand Functions 59

NetCommand®-Controlled Recordings

Setting up Recordings

Figure 7

Through NetCommand, you can automatically start and

stop recordings and send signals from one playback

device to a recording device. Recordings can be made

on recordable devices connected to the TV or to the

internal TV Disc. The TV Disc is an IEEE 1394 hard disk

drive and is available for all channels from CableCARD™,

Ant 1, Ant 2, and IEEE 1394 devices or tuning devices

(cable boxes or satellite receivers) connected to

inputs 1–3. The capacity of the TV Disc is 160 GB on

models WD-62827/WD-73827 and 250 GB on models

WD-62927/WD-73927.

The TV can convert digital channels and IEEE 1394

digital signals to analog signals that can be recorded

on NetCommand-compatible analog VHS and S-VHS

VCRs. It can convert analog channels to digital signals

for recording on the TV Disc or other digital recording

device.

You can schedule the recording to take place at a later

time and program the recording duration for a minimum

of 30 minutes and a maximum of six hours (in 30-minute

increments). The default is one hour. During the

recording, you can view a different device or power off

the TV.

Figure 7. Recording Setup screen

Recording Now

Can be used when viewing Antenna 1 or 2, an IEEE 1394

device, or a non-recording traditional device connected

to Inputs 1–3..

To initiate recording now:

1. Press REC (record) on the TV remote.

2. In the “Record to” section, review the destination

device and duration. Use ADJUST

or to change,

if necessary.

3. Press a second time to start recording.

Time-Delayed Recording

1. Set the TV to the source you want to record.

2 Press REC (record) on the TV remote.

3. Press ADJUST to move the highlight to the

settings you wish to change. Press ADJUST to

change the source, channel (if available). Record To

device, duration, and day of the week. To change

the start time, highlight the Start Time box and press

ENTER to move among the hour, minute, and am/pm

settings. Use ADJUST

to change the settings.

4. Highlight Add and press ENTER to add the recording

to the record list. If your selection is successful, a

confirmation message will be displayed. If you pick

overlapping times, day(s), or destination devices, you

will see a message stating there is a conflict.

5. To exit, press HOME on the TV remote after all

recordings have been added.

Record List

Figure 8

Press GUIDE while viewing the Recording Setup screen

to see a list of all currently scheduled recordings. A

maximum of 32 recordings can be scheduled.

Time-delayed recordings scheduled through TV Guide On

Screen® are not listed in this screen. See the TV Guide

On Screen User’s Manual for information on recording

using the TV Guide On Screen system.

To cancel a recording on the Record List, press ADJUST

or to select the recording, then press CANCEL. To page

through the list, press CH or .

Figure 8. Record List screen

IMPORTANT

• Signalsfromdevicesconnectedtothe

HDMI, Component, or PC inputs cannot be

recorded.

• TVDisccannotrecordDVvideofroma

camcorder.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-73827 Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info