475334
13
Zoom out
Zoom in
Vorherige Seite
1/94
Nächste Seite
2. TV Setup 13
Initial TV Setup
Use the Setup menu for basic TV setup options.
Press
1.
MENU
to open the Main menu.
Press
2.
to highlight the Setup icon and display the
Setup menu.
Memorizing Channels
For ANT 1 and ANT 2
To start channel memorization
With the
1.
Setup menu displayed, press to high-
light the Scan icon.
Start channel memorization from the Setup menu.
Press
2.
to highlight an input selection based on
your connections:
Input Condition
Ant 1 Air
Ant 2 Air
When connected to an indoor or
outdoor antenna
Ant 1 Cable
Ant 2 Cable
When connected to direct cable (no
cable box)
Press
3.
to highlight the on-screen START button.
Press
4.
ENTER
to start automatic channel memoriza-
tion.
To stop channel memorization before
completion, press
CANCEL
.
When memorization is complete you can:
5.
• Press
MENU
once to return to the top row of icons.
• Press
MENU
again to return to the Main menu.
• Press
EXIT
to watch TV.
After channels have been memorized:
• To tune to memorized channels, press
CH
/
while watching TV on the
ANT 1
or
ANT 2
inputs.
• UsetheSetup > Edit menu (page 44) for additional
channel options, such as adding or deleting chan-
nels from memory, naming channels, and saving
favorite channels in custom memory banks.
See chapter 5, “TV Menu Settings,” to:
• SettheTVclock(page45)
• SettheTVTimer(page46)
• SelectanEnergyModetomanagepowerusewhile
the TV is off (page 47)
• Selectalampbrightnessmode(page47)
• Enable3Dvideo(pages35and47)
Setting Up TV Inputs
When You First Connect a Device
The TV’s Easy Connect™ Auto Input Sensing feature
detects most connections automatically.
Note: For connection and setup of a personal com-
puter, see the information on page 17.
Auto Input/Auto Output Sensing for Most Devices
When you first connect a device, the TV will:
a. Detect the connected device and automatically
switch to it
b. Prompt you to identify the device type
c. 736 or 835 series TV. Prompt you to perform
NetCommand set-up for the device, if available.
d. Repeat these steps for any additional newly
detected devices
See below for connections which trigger Auto Sensing.
Auto Input Sensing Available
Y/VIDEO
(detected as
composite video)
Y
plus
Pb
(detected as component video)
S-VIDEO
HDMI
*
USB
(USB photo port on front)
INPUT 4 AUDIO
(for an audio-only device; see page 25.)
Auto Output Sensing
Available
DIGITAL AUDIO OUTPUT
(orange jack)
AVR AUDIO OUTPUT
(
red jack)
No Auto Sensing
ANT 1
and
ANT 2
*
If the device is powered off when connected, detec-
tion occurs when the device is next powered on.
Auto Input/Auto Output Sensing for CEC Devices
When the TVs NetCommand for HDMI feature is active,
most CEC-enabled devices are recognized and identified
automatically by the TV. NetCommand for HDMI may
allow you to control functions of a CEC-enabled device.
See Appendix E, “NetCommand HDMI Control of CEC
Devices,” page 77.
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Mitsubishi WD-73835 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info