Bedienungsanleitung Mitsubishi WD-73837 (Seite 79 von 88) (Englisch)

475273

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Appendices 79

Appendix E: Troubleshooting, continued

NetCommand IR Control (NetCommand-equipped models only)

Symptom Remarks

3. The A/V receiver is the selected audio source

but there is no sound.

A/V Receiver Set Up for Audio-Only Switching•

Check to see if the A/V Receiver power is turned on. -

With A/V receiver power turned on, redisplay the Activ- -

ity menu and press ENTER to allow NetCommand to

correctly select the A/V Receiver input.

Incorrect setup in the Inputs > AVR menu. Check the -

device connection assigned in the AVR menu.

A/V Receiver Set Up for Audio and Video Switching over HDMI•

Check to see if the A/V Receiver power is turned on. -

If the device is connected only to the TV (e.g., on ANT -

or a front panel input), verify that the TV’s AUDIO

OUTPUT is connected to the A/V receiver.

The A/V receiver is not switching properly because -

you have not learned the IR codes for the A/V receiver

inputs to which your devices are connected.

4. There is no sound from the A/V receiver

for my DVD player or other surround sound

device even though I learned the IR code for

the A/V receiver’s DVD input or other input.

(A/V Receiver Set Up for Audio-Only Switch-

ing)

NetCommand A/V receiver setup for the DVD player or digital

surround sound device or other device is not switching prop-

erly. See “Case 2: Automatic A/V Receiver Switching to a Sur-

round Sound Device,” page 54, and perform A/V receiver setup

for a digital surround sound device.

5. There is no sound or picture from the A/V

receiver for my DVD player or other device

connected to the A/V receiver; the A/V

receiver should be sending video to the TV

over an HDMI cable.

(

A/V Receiver Set Up for Audio and Video

Switching over HDMI)

The NetCommand A/V receiver setup is not switching audio

and video inputs properly because you did not “learn” the A/V

receiver’s IR codes for the device inputs. See “Case 3: Auto-

matic Audio and Video Switching via HDMI,” page 55.

6. I’ve selected my DVD player or other sur-

round sound device in combination with the

TV speakers but hear no sound from the TV

speakers.

A/V Receiver Set Up for Audio-Only Switching•

If you have only an audio connection from the device to the

A/V receiver, a physical audio connection from the device

to the TV is also required.

Connect the left and right audio output from the device -

to the appropriate TV audio input. Now you can hear

audio from the device through either the TV speakers or

the A/V receiver.

To switch audio sources, press MORE 9 (Audio), press -

to show the Speakers option, then press to

select AV Receiver or TV.

A/V Receiver Set Up for Audio and Video Switching over HDMI•

With your DVD player connected to the A/V receiver, only

video is passed from the A/V receiver to the TV because of

copy-protection restrictions on the HDMI signal

7. I “learned” the RECORD key for my VCR/DVR

but when I pressed the RECORD key, the

VCR/DVR did not record anything.

Check that the VCR or DVR is receiving a signal directly from

your cable box or satellite receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-73837 Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info