Bedienungsanleitung Mitsubishi WD-73838 (Seite 78 von 110) (Englisch)

475257

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

78 Appendices

For assistance call 1(800) 332-2119

Programming the Remote Control

Press one of the upper buttons on the remote

control to change to the correct mode for the

product you want to control. Refer to the table

below. Only one of each device type can be con-

trolled in each mode.

Mode Affected Device

CAB/SAT

Cable Box

DTV Receiver

Satellite Receiver

VCR

DVR

DVD Player/Recorder

DVD

DVD Player/Recorder

DVR

VCR

AUDIO

A/V Receiver

Audio Amplifier

CD Player

Press and hold

POWER

on the remote control for

several seconds until the key flashes twice and

goes off.

Release the

POWER

key.

Enter the first five-digit code listed for your equip-

ment in the reference tables that follow.

If you need to start over or wish to exit

programming mode, temporarily change to a

different device mode.

Point the remote control at the equipment and

press

POWER

. If the product has no power on/off

function, press a different key, such as (

PLAY

(

STOP

VOLUME UP

, or

MUTE.

• If the equipment responds, the remote control

is properly programmed.

• If the equipment does not respond, repeat

steps 4 and 5 with the next five-digit code

listed for your equipment.

Once you have found the correct code, write it in

the space below for future reference.

Mode

Device Type Code

CABLE/SAT

VCR

DVD

AUDIO

IMPORTANT

You may need to reprogram the remote control after

changing the batteries. Record the codes for each

mode in the space provided to make this faster.

Code Verification

To determine the code programmed for any mode:

Set the mode to the one you wish to verify.

Press and hold

POWER

on the remote control for

several seconds until the

key

flashes twice and goes

off.

Press keys

9 9 0

Press

and count the flashes of the power key.

Write down the number of flashes as the first digit

of the code.

Repeat step 4 for the other digits of the code.

Press

to see flashes for the second digit, press

for the third digit,

for the fourth digit, and

for the

fifth digit.

Audio Lock: Universal A/V Receiver

Control

With Audio Lock enabled, the remote control oper-

ates volume and mute on an A/V receiver in all control

modes. Activate Audio Lock if you always use an A/V

receiver with your TV and other A/V equipment.

Program

AUDIO

mode for your A/V receiver as

described in “Programming the Remote Control” on

this page.

With the remote control in

AUDIO

mode, hold

POWER

on the remote control for several seconds until the

key flashes twice and goes off.

Press keys

9 9 3 ENTER

The

POWER

key will flash twice to indicate Audio

Lock is active.

To Reset the Remote Control to Operate Volume

and Mute for the TV Speakers

Press and hold

POWER

for several seconds until it

flashes twice and goes off.

Press keys

9 9 3 VOLUME UP

The

POWER

key will flash four times to indicate Audio

Lock has cleared.

Appendix A: Programming the Remote Control, continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-73838 Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info