Bedienungsanleitung Mitsubishi WD-73C8 (Seite 76 von 94) (Englisch)

475327

Zoom out

Zoom in

Vorherige Seite

1/94

Nächste Seite

76 Appendices

Lamp-Cartridge Replacement

Removing the Old Lamp Cartridge

Turn off TV power and allow the lamp to cool for at

least one hour before proceeding.

After the lamp has cooled, remove the cover of the

lamp compartment, located on the back of the TV.

Refer to figures 1 and 2. Use a #2 (large) Phillips

screwdriver to loosen the screw securing the cover.

Keep the screw and cover for re-installation

th a large Phillips screwdriver, loosen the two

shiny screws securing the lamp cartridge until they

disengage from the mating threads. These are

captive screws and cannot be separated from the

lamp cartridge.

Fully open the bag supplied with the replacement

lamp and set the opened bag aside.

Gently grasp the handle of the lamp cartridge and

pull the old cartridge straight out. See figure 3.

CAUTION: Do not tilt or rotate the cartridge, as

small glass fragments may fall out.

Without tilting or putting down the lamp cartridge,

insert it into the opened bag. Close the bag while

being careful not to let any glass particles fall out.

Installing the New Lamp Cartridge

Do not touch the glass parts of the new lamp car-

tridge. Insert the new cartridge into the TV in the

same orientation as the old cartridge. Push on the

cartridge housing until it is fully seated.

With either your fingers or the screwdriver, gently

tighten the two shiny screws. If using a screwdriver,

AVOID OVERTIGHTENING!

Replace the plastic cover and retaining screws.

WASH YOUR HANDS THOROUGHLY, AS THIS

LAMP CONTAINS MERCURY.

Disposal of the Old Lamp Cartridge

Lamp under warranty: All lamps replaced under war-

ranty must be returned to Mitsubishi. Use the return

shipping label provided and send to Mitsubishi Digital

Electronics, America, 1001 Cherry Drive, Suite 2, Brasel-

ton, GA 30517.

IMPORTANT: Lamps found to be without defect will

be returned and charged back to the sender.

Lamp no longer under warranty:

Contact your

local authorities or the Electronic Industries Alliance at

www.eiae.org for lamp-disposal or recycling instructions.

Do not dispose of the old lamp with common trash.

Figure 3

Use only replacement lamp part number

915B403001.

Figure 4

Keep lamp

cartridge horizontal

and remove dust

from the mesh filter

using a vacuum

cleaner or soft dry

brush.

Figure 2

Figure 1

Lamp-Cartridge Filter Cleaning

If the TV shuts off after displaying the message “TV

will shut down in a few seconds. Please check if the

air flow is blocked ” and/or the

STATUS

LED is yellow, the

air filter may need cleaning. The air filter is part of the

lamp cartridge. Use the following procedure to clean

the filter.

Remove the lamp cartridge from the TV as

described under “Removing the Old Lamp Car-

tridge.” Do not tilt or rotate the cartridge. Do not

touch the glass parts of the lamp cartridge.

Holding the lamp cartridge horizontal (do not tilt or

rotate), use a soft dry brush or vacuum cleaner to

remove any dust that may be present on the mesh

filter. Do not use liquids. See figure 4.

Reinstall the lamp cartridge as described under

“Installing the New Lamp Cartridge.”

Appendix D: Lamp-Cartridge Replacement and Cleaning, continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-73C8 Seite 76

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info