Bedienungsanleitung Mitsubishi WD-82842 (Seite 38 von 62) (Englisch)

475231

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

For assistance call 1(800) 332-2119

HDMI Control of CEC Devices

If prompted for a name, high-

light a name for the device

and press

ENTER

to add a

check. The device itself may

later override the name you

assign.

Highlight On and press

ENTER

to add a check.

Press EXIT to close the New Device Found screen.

Note: At any time after completing Auto Input Sens-

ing, you can set the TV’s HDMI control on or off

in the Inputs > HDMI Control menu.

Many newer HDMI devices have a feature called

Consumer Electronics Control (CEC) or HDMI Control.

HDMI Control allows one device, such as the TV, to

control other devices, such as an A/V receiver or disc

player. Use of CEC is optional.

Each manufacturer chooses which CEC functions to

support so it is difficult to predict which devices and

features are compatible with Mitsubishi’s HDMI Control.

You may find that CEC functions for a specific device are

limited.

To use HDMI Control, you must enable it in both

the TV and the device.

• In the TV. Enable HDMI control from the New

Device Found screen or from the Inputs > HDMI

Control menu.

• I

n the Device. Most devices with HDMI CEC com-

patibility let you turn it on or off in the device menus,

where it is typically listed as “HDMI Control.”

Enabling HDMI Control

of CEC Devices

To ensure proper detection

• Power on HDMI devices before connecting

them to the TV.

• Connect and set up HDMI devices one at a

time.

Power on the device and allow it to complete the

power-on sequence (boot up). Stop any playback.

Connect the device to one of the TV’s HDMI inputs.

When the TV detects the connection, the New

Device Found screen will appear.

Note: See “If the New Device Found Screen Has No

HDMI Control Option” on this page if an HDMI

Control option is not offered.

New Device Found screen with HDMI Control option.

This screen displays only if the device’s HDMI Control is

enabled

If the New Device Found Screen

Has No HDMI Control Option

If the New Device Found screen shows no option for

HDMI Control, one of these conditions applies:

• HDMI Control is turned off in the menus of the

new device

Action:

a. Press EXIT to close the New Device Found

screen.

b. Display the device’s setup menus and enable

the device’s CEC capabilities.

c. Wait for the TV’s New Device Found screen

to appear again.

d. If the New Device Found screen does not

appear, power off the device. Power on the

device and wait for the New Device Found

screen to display with the HDMI Control

option.

• The HDMI cable cannot support CEC

Action:

Upgrade your HDMI cable to one that supports

CEC.

• The device does not have CEC compatibility

Action:

Control the device with its own remote control or

program the TV’s remote control to operate the

device.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-82842 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info