Bedienungsanleitung Mitsubishi WD-82CB1 (Seite 25 von 56) (Englisch)

475246

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

2. TV Menus 25

For assistance call 1(800) 332-2119

Setup, continued

Setup Cha nnel

Ant Air,

Ant Cable

You must perform a channel scan to receive digital channels. The scan searches for broad-

cast channels and adds them to TV memory. To start channel scan:

1. Highlight one of the input selections based on your connection to the

ANT input

• Air when connected to an indoor or outdoor antenna.

• Cable when connected to direct cable (no cable box)

2. Select the scan type.

• Select All Channels for an initial scan or after moving the TV to an new area with a differ-

ent channel line-up.

• Select Add only new channels to search for channels newly broadcasting since the

previous scan.

3. Press

to highlight SCAN.

4. Press

ENTER

to start channel memorization.

See below for additional notes on Scan.

All Channels,

Add only new

channels

Scan

E dit After channel scan, Edit lets you add and delete memorized channels. Memorized channels are

those you can tune using the

key. Edit the channel list to limit tuning to channels you watch.

• Press

CH/PAGE

to jump to the next or previous page of channel numbers.

• Press to move through all channel numbers, one at a time.

Adding/Deleting Channels Using the Channel Edit Menu

• Channels marked with a check are in memory.

• To add or delete a channel from memory, highlight

the channel number and press

ENTER

• To add a single digital channel not in the list, see the

notes under Scan on this page .

• Digital channels are listed by virtual channel number

with the physical channel number shown in small

gray text.

- Virtual Channel Number (digital channels only).

A channel number sent by a local broadcaster.

- Physical Digital Channel Number. The

channel number officially assigned to the actual

broadcast frequency; shown on screen in gray

text.

Notes on Sca n and Channel Memorization

• Channel memorization may take up to 15 minutes to

complete.

•

To stop channel memorization before completion, press

CANCEL

Channels already added are retained

• When watching TV, press

to move through

memorized channels. Press and hold

to speed

through channels.

•

To add a digital channel that does not appear in the

Edit menu without performing channel memorization:

1. Look up the physical channel number for

the new digital channel. See the website

www.antennaweb.org for help.

2. Press

INPUT

and select the

ANT

input.

3. Use the number and

CANCEL

keys to enter the

physical channel number followed by “-1” and

ENTER

. For example, for physical channel 36,

ENTER

The TV will search for a digital channel on the channel 36

frequency. When it finds the channel, it will:

a. Add the channel to memory.

b. Change the channel number to the virtual

channel number sent by the broadcaster.

c. Add to memory any associated sub-chan-

nels.

• Rememorize channels if you move the TV to a different

geographic area with a different channel line-up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD-82CB1 Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info