Bedienungsanleitung Mitsubishi WD3300U (Seite 11 von 52) (Englisch)

493649

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

EN-11

Setting up your projector (continued)

Adjusting the position of the projected image

To adjust the positions of the projector and the screen, use LENS SHIFT button.

1. Press the LENS SHIFT button.

• The LENS SHIFT menu appears at the center of the screen.

2. Press the , ,  or  button to move the image position.

• When the  button is pressed, the image moves down.

• When the  button is pressed, the image moves up.

• When the  button is pressed, the image moves to the right.

• When the  button is pressed, the image moves to the left.

• WhentheENTERbuttonispressedwhiletheLENSSHIFTmenuisdisplayed,theshiftmodecanbeswitched

between FAST and STEP. When FAST is selected, the lens shifts in a large amount with the , ,  or  button,

and it shifts in a small amount when STEP is selected.

• WhentheLENSSHIFTmenuisdisplayedwhilenovideosignalisinputtotheprojector,acrosshatchappearson

the entire screen.

• Becarefulnottobecaughtintheopeninginthelenswhilethelensismoving.

• Whilethelensshiftisworking,thescreenmayicker.

Correcting skewed or distorted image

For the best projection, project images on a ﬂat screen installed at 90 degrees to the ﬂoor. If necessary, tilt the

projector using the two adjustment feet on the bottom of the projector.

1. Tilt up the projector to the appropriate angle.

2. Rotate the adjustment feet for ﬁne adjustment.

Important:

• Don’ttransporttheprojectorwithitsadjustmentfeetextended.Otherwisethe

adjustment feet may be damaged.

When ﬁne streaks are seen on projected images

This is due to interference with the screen surface and is not a malfunction. Replace the screen or displace the focus

a little. (See page 16 or 23 for focus adjustment.)

When projected images are distorted to a trapezoid

When the screen and the projector are not placed perpendicularly to each other, projected images become

trapezoidal. If you cannot make the projector and the screen perpendicular to each other by mechanical adjustments,

adjust keystone.

To adjust keystone:

Press the KEYSTONE button on the projector or the

remote control to display KEYSTONE, and adjust

the image by pressing the , ,  or  button (or

VOLUME+or-buttonontheremotecontrol).

LENS

SHIFT

FAST

SELECT:ENTER

Adjustment feet

Screen

In the following cases (for front projection):

Press the



(or -) button.

Press the



(or+)button.

Press the



button.

Press the



button.

Important:

• Forproperkeystoneadjustmentresults,resetthelenstothefactory-adjustedpositionusingLENSSHIFTRESET

in the INSTALLATION menu before carrying out keystone adjustment. (See page 30.)

• When the keystone adjustment is carried out, the adjustment value is indicated. Note that this value doesn’t mean

a projection angle.

• Theallowablerangeoftheadjustmentvalueinthekeystoneadjustmentvariesdependingontheinstallation

conditions.

• Whenthekeystoneadjustmenttakeseffect,theresolutiondecreases.Inaddition,stripesmayappearorstraight

lines may bend in images with complicated patterns. They are not due to product malfunctions.

• Whenthekeystoneadjustmentisperformed,thedisplayedimagemaybedistorted.

• Dependingontheinstallationconditionsoftheprojectorandthescreen,aperfectrectangularimageandthe

proper aspect ratio may not be obtained.

• Noisemayappearonthescreenduringthekeystoneadjustmentbecauseofthetypeofthevideosignalbeing

projected and the setting values of the keystone adjustment. In such cases, set the keystone adjustment values in

the range where the image is displayed without noise.

• Whenhorizontalandverticalkeystoneadjustmentsareperformedincombination,theadjustablerangebecomes

narrower than in the case when they are performed separately.

• Inthekeystoneadjustmentwiththeoptionlens,theproperaspectratiomaynotbeobtained.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD3300U Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi WD3300U

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info