Bedienungsanleitung Mitsubishi WD380U-EST (Seite 15 von 60) (Englisch)

493667

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

EN-15

Preparation

Preparation for projection

1. Attach the provided power cord to the projector.

2. Plug the power cord in the wall outlet.

3. Remove the lens cap.

Warning:

•

Do not look into the lens directly when the projector is on.

•

The lens cap is for protecting the lens. If you leave

the lens cap on the lens with the projector turned

on, it may be deformed because of heat build-up.

Remove the lens cap when you turn on the projector.

• OneofpowercordsfortheU.S.,Europe,U.K.and

Korea is provided appropriately.

•

This projector uses the power plug of three-pin

grounding type. Do not remove the grounding pin from

the power plug. If the power plug doesn’t ﬁt your wall

outlet, ask an electrician to change the wall outlet.

• IncasethatthepowercordfortheU.S.isprovided

with this projector, never connect this cord to any

outlet or power supply using other voltages or

frequencies than rated. If you want to use a power

supply using other voltage than rated, prepare an

appropriate power cord separately.

• Use100-240VAC50/60Hztopreventreor

electric shock.

•

Do not place any objects on the power cord or do

not place the projector near heat sources to prevent

damage to the power cord. If the power cord should

be damaged, contact your dealer for replacement

because it may cause ﬁre or electric shock.

•

Do not modify or alter the power cord. If the power cord

is modiﬁed or altered, it may cause ﬁre or electric shock.

Caution:

• Pluginthepowercordrmly.Whenunplugging,

hold and pull the power plug, not the power cord.

• Donotpluginoroutthepowercordwithyour

hand wet. It may cause electric shock.

Important:

• WhenStandbyModeintheInstallationmenuis

set to LAN, Speaker Out, or Monitor Out, the fans

rotate at very low speed during standby after

plugging the power cord (with 5 second high speed

rotation at the beginning) and after turning off the

lamp. This is to cool down the projector operating

various functions during standby and is not a

malfunction. (When Standby Mode is set to Low,

the fans stop during standby.)

Adjustment of the projection angle

For the best projection, project images on a ﬂat screen

installed at 90 degrees to the ﬂoor. If necessary, tilt the

projector using the two adjustment feet on the bottom

of the projector.

Using the adjustment feet (front)

1. Tilt up the projector to the appropriate angle.

Rotate the adjustment feet (front) for ﬁne adjustment.

Important:

•

Install the screen on a ﬂat wall at 90 degrees to the ﬂoor.

• Slantingtheprojectormorethan±10°(rightand

left)or±15°(frontandrear)maycausetroubleor

explosion of the lamp. You can tilt the projector up

to 8 degrees using the adjustment feet only.

• Imagesmaynotbeprojectedinashapeofa

regular rectangle or with its aspect ratio 4:3,

depending on the installation conditions of the

projector and the screen.

• WhenAutoKeystoneintheInstallationmenuisset

to On, this projector automatically corrects vertical

keystone distortion. For ﬁne adjustment, press the

KEYSTONE button on the projector or the remote

control to display Keystone, and adjust the image

by pressing the ,  button (or VOLUME , 

button on the remote control).

In the following cases:

Press the



button. Press the



button.

• Theautomatickeystoneadjustmentmaynot

be carried out correctly because of the ambient

temperature and the installation conditions of the

projector and the screen. In such cases, correct the

keystone manually.

• Whentheprojectorisprojectingimageswhere

acceleration is present, such as in a vehicle and

aircraft, the automatic keystone adjustment may

not function correctly. In such a case, set Auto

Keystone in the Installation menu to Off and correct

the keystone manually.

• Youcancorrecttheverticalkeystones.However,

their adjustment ranges are limited in such

correction.

Important:

• Whenthekeystoneadjustmentiscarriedout,the

adjustment value is indicated. Note that this value

doesn’t mean a projection angle.

• Theallowablerangeoftheadjustmentvaluein

the keystone adjustment varies depending on

the installation condition, input signal and aspect

settings in MENU.

• Whenthekeystoneadjustmenttakeseffect,the

MAGNIFY mode and the Overscan function cannot

be used.

• Whenthekeystoneadjustmenttakeseffect,the

resolution decreases. In addition, stripes may

appear or straight lines may bend in images with

complicated patterns. They are not due to product

malfunctions.

• Noisemayappearonthescreenduringthe

keystone adjustment because of the type of the

video signal being projected and the setting values

of the keystone adjustment. In such cases, set the

keystone adjustment values in the range where the

image is displayed without noise.

• Whenthekeystoneadjustmentiscarriedout,the

image may not be displayed correctly because of

the type of input signal.

Mitsubishi WD380U-EST Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi WD380U-EST

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info