Bedienungsanleitung Mitsubishi WD62527 (Seite 100 von 110) (Englisch)

32989

100

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

100

Chapter 6. Special Features

30. The A/V Receiver is the selected audio source

but there is no sound.

• Check to see if the A/V Receiver power is turned on. After the power

is turned on, redisplay the Device Selection menu and press ENTER

to allow NetCommand to correctly select the A/V Receiver input.

• From the NetCommand menu, select Review. Check the Review

screen to see if the input for the A/V Receiver assigned to the

corresponds to the actual connections on the A/V Receiver. If

they do not match, either change the actual connections, or select

Change on the Edit NetCommand menu to change the device on the

Connection screen.

31. The TV Speaker icon or A/V Receiver icon is

grayed out and not selectable.

Select the Change setting from the Edit NetCommand menu, and then

select the device (for example VCR). Once the Connection screen is

displayed, check if the audio check box is selected for the TV input

and/or AVR input.

32. Cannot see the A/V Receiver menu. The A/V Receiver is not connected to any input of the TV. To check the

A/V Receiver menu, temporarily plug into an unused input of the TV,

such as Input 3 (on front). Then select Review from the NetCommand

Menu, turn the input On to view the A/V Receiver menu.

33. Screen is black when trying to view digital

channels or IEEE 1394 device.

The PerfectColor™ color balance has been incorrectly set. Reset the

color balance by repeatedly pressing the Video button on the remote

until the PerfectColor option appears. Press ENTER, then CANCEL

34. The REC button is not working, or, on the

Transport menu the record key is grayed out and

not available.

• The device does not support recording, such as a DVD player.

• Recordings can not be initiated from the Transport menu when using

an IEEE 1394 device. Select the source that will be recorded from the

Device Selection menu and press REC. The Record menu displays

allowing setup of a recording.

35. A program recorded from your TV is distorted

when played on a 4:3 TV.

TV was set to Anamorphic when program was recorded. Record

programs in Cropped mode if playing back on a 4:3 TV.

36. Excessive digital artifacts. • The IEEE 1394 cable is too long (15 feet between devices is the

maximum length).

• There may be a slow device in the middle of the IEEE 1394 network.

Move the slow devices to the end so that connections for faster

devices do not pass through them.

37. Cannot see a picture from a DV Camcorder. • Go to Device Selection menu and select analog connection.

• Connect the DV Camcorder to analog input (for example, Input-3).

Select NetCommand from the main menu, then Change. At the

Change screen, select the camcorder. On the Name screen, check

Analog Connection. Select the device and on the following screen,

select which analog input was used, and check audio and/or video.

38. DVCR analog/digital problems. If the tape is currently playing but no picture displays, there may be a

mismatch of the medium with the display. Press DEVICE to display the

Device Selection menu. Press ENTER for the DVCR device. If digital is

selected, try analog, or if analog is selected, try digital.

39. D-VHS recordings for digital cable have drop-

outs (loss of picture or sound), or no playback.

Digital cable signals on IEEE 1394 can exceed the data rate standards

supported by DVCR.

40. There is no audio and video from the IEEE 1394

device.

• The device is not turned on - turn the device power on.

• No medium (tape or disc) is inserted into the device.

• The medium is blank (has no recording).

• The play command failed - Try pressing play again on the device’s

remote control or front panel.

• The device is already in use (for example: the device is currently

recording).

• The source is copy-protected or violates copy protection.

• The device’s digital video signal is not supported by the TV, such

as DV video, common with camcorders. Use analog connections

instead, if available.

• The device is not an audio/video device.

• Too many other devices are already communicating over IEEE 1394.

Remove or stop some devices and try again.

Problem Possible Solution

Troubleshooting, continued

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD62527 Seite 100

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info