Bedienungsanleitung Mitsubishi WD62528 (Seite 31 von 110) (Englisch)

32987

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

Chapter 2. Connecting

Connecting the IR Emitter NetCommand

% * ( * 5 " -

46 33 06 /%

"73FDFJWFS

0UIFS"7EFWJDF











Net Command

IR EMITTER

',INK

57CBDLQBOFMTFDUJPO

Figure 13. Connecting IR Emitter NetCommand

IR Emitter NetCommand®

Figure 13

A double IR Emitter cable is included with models

WD-52527 and WD-62527. A Quadruple IR Emitter cable is

included with models WD-52528 and WD-62528.

The emitters connected to these jacks are used by the

NetCommand system to control other devices such as

VCRs, DVD players, Cable boxes and Satellite receivers.

1. Connect the plug end of the supplied IR Emitter Cable

to either one of the IR Output NetCommand jacks on

the TV back panel.

2. Run the cable for each of the emitter ends under,

along side or over the top of each device to be

controlled to the area of the front where the remote

control sensor is located.

3. Place the emitter end in front of the remote control

sensor of the device to be controlled. The emitter

bulb should face the remote control sensor. This bulb

emits infrared light in a cone shaped pattern. The

bulb needs to be placed far enough from the remote

control sensor to allow the cone pattern to include

the sensor.

The remote control sensor is usually behind the plastic

window of the front display panel. It is sometimes

visible when you look through the display plastic using

a flashlight and is normally a round or square cutout

If a single emitter

end can be placed

in a position that

will operate more

than one device, do

not use a separate

emitter end for the

additional device.

A single device

receiving remote

control signals from

too many emitters

or remote controls

may not respond

at all.

IMPORTANT

behind the plastic. If you cannot see the sensor and the

device’s Owner’s Guide does not specify the location,

you can find it by using the device’s remote control.

Hold the remote about 1/2 inch from the front of the

device. Starting from one end of the display window

plastic, press the POWER button.

If the device does not respond, move the remote control

1 inch toward the center and try again. Repeat this

until the device responds. Note this location then start

over from the other end of the display window plastic,

repeating until the device responds again. The remote

control sensor will be somewhere between these two

positions. This is usually enough accuracy for the

placement of the IR emitters.

• With some devices, the emitter will work better

facing downward from the top of the device. Some

experimentation may be needed.

• The emitter end being used can be secured in place

using double stick tape.

• If you are not going to

be using all emitter ends, place

the unused ends behind the devices so that they

cannot send signals to the remote control sensors.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD62528 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info