Bedienungsanleitung Mitsubishi WD8700U (Seite 36 von 79) (Englisch)

549862

Zoom out

Zoom in

Vorherige Seite

1/79

Nächste Seite

EN-36

MULTI-SCREEN menu

MULTI-SCREEN

EDGE BLENDING

SETTING

OFF

EDGE ADJUST

COLOR MATCHING

SETTING

MEASURED DATA

MANUAL

MEASURE

opt.

ITEM SETTING FUNCTION

EDGE BLENDING OFF Select when using the projector alone.

ON Select when using the projector to conﬁgure the multi-screen consisting

of multiple projectors.

The following settings in the SETTING become enabled to make the

overlapped area of the displayed images unnoticeable.

SETTING EDGE ADJUST Use to make the overlapped area of the screens unnoticeable in the

multi-screen application. Use this setting to select the edges to be

overlapped or to set the overlapped areas. (See page 49.)

BLACK LEVEL

In the multi-screen application, the black level in the areas where images

are overlapped will become bright. So, use this setting to adjust the

black level in non-overlapped areas. (See page 49.)

BRIGHT UNIFORMITY

CORRECTION

Use to correct non-uniformity in the screen brightness of the single

projector to facilitate edge blending. (See page 49.)

RESET Use to reset the values of EDGE ADJUST , BLACK LEVEL and

BRIGHT UNIFORMITY CORRECTION to the defaults.

COLOR MATCHING OFF Select this option when the projector is used alone.

MANUAL Select this option when adjusting colors while viewing the screen to

correct color variations among the projectors.

MEASURE Select this option when adjusting colors using a measuring instrument

to correct color variations among the projectors.

MANUAL SETTING The test signal is displayed. Make adjustment so that the color tones of

each image match among the adjoining projectors. (See page 50.)

RESET Use to reset the value of SETTING in the MANUAL to the default.

MEASURE MEASURED DATA The test signal is displayed. Measure the brightness and chromaticity of

each image using a measuring instrument (chroma meter) and enter the

measurement values. (See page 50.)

TARGET DATA Use to set the target chromaticity value of each color. (See page 50.)

RESET Use to reset the values of MEASURED DATA and TARGET DATA in

the MEASURE to the defaults.

• WhenEDGEBLENDINGisONorCOLORMATCHINGisMANUALorMEASURE,COLORENHANCERintheIMAGEmenuis

set to MULTI-SCREEN. In this case, you cannot set any other items than MULT-SCREEN.

• Theedgeblendingfunctioncanbeusedwithnon-directionalscreens.Ifyouuseadirectionalscreen,theareaswhereimages

are overlapped seem discontinuous depending on the viewing angle.

• ThetargetchromaticityvalueenteredforTARGETDATAintheMEASUREmenuisjustforguidance.Iftheobtainedresult

doesn’t match with the colors displayed on the adjoining projectors, adjust the value while viewing the screens.

Menu operation (continued)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WD8700U Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Mitsubishi WD8700U

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info