Bedienungsanleitung Mitsubishi WL-82913 (Seite 37 von 140) (Englisch)

475290

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Connecting the IR Emitter NetCommand

or IR Repeater

  







 

      

   









 







 



 

 



 



Figure 16. Connecting IR Emitter NetCommand or IR

Emitter Repeater

IR Emitter NetCommand

or IR

Emitter Repeater

Figure 16

IR Emitter NetCommand

The emitters connected to these jacks are used by the

NetCommand system to control other devices such as

VCR, DVD players, Cable boxes and Satellite receivers.

1A.Connect the plug end of the supplied Quadruple IR

Emitter Cable to one of the IR Output NetCommand

jacks on the TV back panel.

OR ...

IR Emitter Repeater

The emitters connected to these jacks are not used by

NetCommand, but will repeat any IR command received

by the TV. These emitters allow the TV to be the remote

control sensor for other devices outside the range of the

hand-held remote control. Do not use these repeaters

with devices that can receive the remote control signal

directly, as the signals can interfere with each other.

1B.Connect the IR emitter to IR EMITTER-REPEATER on

the TV back panel.

If a single emitter end can be placed in a position that will operate more than one device, do

not use a separate emitter end for the additional device. A single device receiving remote

control signals from too many emitters or remote controls may not respond at all.

IMPORTANT

After you have used 1A or 1B,

2. Run the cable for each of the emitter ends under, along

side or over the top of each device to be controlled to

the area of the front where the remote control sensor is

located.

3. Place the emitter end in front of the remote control

sensor of the device to be controlled. The emitter bulb

should face the remote control sensor. This bulb emits

infrared light in a cone shaped pattern. The bulb needs

to be placed far enough from the remote control sensor

to allow the cone pattern to include the sensor.

The remote control sensor is usually behind the plastic

window of the front display panel. It is sometimes

visible when you look through the display plastic using a

flashlight and is normally a round or square cutout behind

the plastic. If you cannot see the sensor and the device’s

Owner’s Guide does not specify the location, you can find

it by using the device’s remote control. Hold the remote

about 1/2 inch from the front of the device. Starting from

one end of the display window plastic, press the POWER

button.

If the device does not respond, move the remote control 1

inch toward the center and try again. Repeat this until the

device responds. Note this location then start over from

the other end of the display window plastic, repeating until

the device responds again. The remote control sensor

will be somewhere between these two positions. This

is usually enough accuracy for the placement of the IR

emitters.

4. With some devices, the emitter will work better

facing downward from the top of the device. Some

experimentation may be needed. If you are not going

be using all emitter ends, place the unused ends

behind the devices so that they cannot send signals to

the remote control sensors.

5. The emitter end being used can be secured in place

using double stick tape.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi WL-82913 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info