Bedienungsanleitung Mitsubishi wl2650u (Seite 39 von 47) (Englisch)

216162

Zoom out

Zoom in

Vorherige Seite

1/47

Nächste Seite

EN-39

To replace the lamp:

1. Unplug the power cord.

2. Loosen the screw (a) using a Phillips screwdriver (+), and

remove the lamp cover (b).

3. Loosen the screws (c) using a Phillips screwdriver (+).

4. Pull the handle.

5. Pull out the lamp box by the handle while holding the

projector.

• Pull the lamp box out of the projector slowly. If it is

pulled out quickly, the lamp may break scattering glass

fragments.

• Do not spill liquid on the removed lamp box or do not

place it near any ﬂ ammable object or where children

can reach to prevent injury or ﬁ re.

6. Load a new lamp box securely into the projector in the right

orientation.

7. Put the handle back to the original position.

• Make sure that the handle is locked.

8. Tighten up the screws (c) using a Phillips screwdriver (+).

9. Tighten up the screw (a) using a Phillips screwdriver (+) to

secure the lamp cover.

Reset of the lamp operation time

Plug in the power cord and reset the lamp operation time by

holding down the

, and POWER buttons on the control

panel at the same time about three seconds.

Important:

• Unless these 3 buttons are pressed at the same time, the lamp operation time isn’t reset.

• Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully.

• The projector doesn’t turn on if the lamp cover isn’t attached securely.

• Be sure to reset the lamp operation time whenever you replace the lamp.

• Do not reset the lamp operation time unless you replace the lamp.

When removing the lamp from the ceiling-mounted projector

When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the

projector or option lamp to prevent glass fragments from scattering.

• Assemble the lamp replacement tray according to the procedure shown on it.

(a)

(b)

(c)

(a)

Important:

• The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.

Caution:

• This projector uses a lamp that contains mercury. Disposal of the lamp or the projector

with the lamp may be regulated due to environmental considerations. For disposal or

recycling information, please contact your local authorities or the Electronic Industries

Alliance: www.eiae.org. (For the U.S. only.)

1. Follow steps 1 to 4 shown above.

2. Attach the lamp replacement tray to the projector as shown

in the ﬁ gure.

3. Secure the lamp replacement tray on the projector using

the tape packed with the tray.

4 Pull out the lamp box by the handle while holding the

projector.

• Hold the lamp replacement tray to prevent glass

fragments from scattering.

• Don’t put the lamp directly on the lamp replacement

tray because it may fall.

5. Detach the lamp replacement tray together with the

removed lamp.

Tape

Replacing the lamp (continued)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Mitsubishi wl2650u Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info